YASKAWA F7 User Manual page 194

http://www.aotewell.com
Parameter Parameter Name
No. Digital Operator Display
H4-02 Terminal FM Gain Setting
Terminal FM Gain
H4-03 Terminal FM Bias Setting
Terminal FM Bias
Terminal AM Monitor
H4-04 Selection
Terminal AM Sel
H4-05 Terminal AM Gain Setting
Terminal AM Gain
H4-06 Terminal AM Bias Setting
Terminal AM Bias
Terminal FM Signal Level
H4-07 Selection
FM Level Select 1
Terminal AM Signal Level
H4-08 Selection
AM Level Select 2
Drive Node Address
H5-01
Serial Comm Adr
Communication Speed
H5-02 Selection
Serial Baud Rate
Communication Parity
H5-03 Selection
Serial Com Sel
Stopping Method After
H5-04 Communication Error
Serial Fault Sel
Communication Fault
H5-05 Detection Selection
Serial Flt Dtct
Drive Transmit Wait Time
H5-06
Transmit WaitTIM
RTS Control Selection
H5-07
RTS Control Sel
Unit Selection for
H5-10
MEMOBUS Register 0025H
<3021>
MEMOBUS 25H UNIT
Terminal RP Pulse Train Input
H6-01 Function Selection
Pulse Input Sel
H6-02 Pulse Train Input Scaling
Pulse In Scaling
H6-03 Pulse Train Input Gain
Pulse Input Gain
Denotes that parameter can be changed when the Drive is running.
Note: Some digital outputs are control method dependent.
Tel: +(86) 755 8660 6182
Aotewell
Table A.1 F7 Parameter List (Continued)
Description
Sets terminal FM output level when selected monitor is at 100%.
Sets terminal FM output level when selected monitor is at 0%.
Selects which monitor will be the output on terminals AM and FC.
Same function choices as H4-01.
Sets terminal AM output voltage (in percent of 10Vdc) when
selected monitor is at 100% output.
Sets terminal AM output voltage (in percent of 10Vdc) when
selected monitor is at 0% output.
Selects the signal level of terminal FM.
0: 0 to 10Vdc
1: -10 to +10Vdc
2: 4 to 20mA*
Selects the signal level of terminal AM.
0: 0 to 10Vdc
1: -10 to +10Vdc
2: 4 to 20mA*
Serial Communications Setup
Selects Drive station node number (address) for Modbus terminals
R+, R-, S+, S-. The Drive's power must be cycled for the setting to
take effect.
Selects the baud rate for Modbus terminals R+, R-, S+ and S-. The
Drive's power must be cycled for the setting to take effect.
0: 1200 bps
1: 2400 bps
2: 4800 bps
3: 9600 bps
4: 19200 bps
Selects the communication parity for Modbus terminals R+, R-, S+
and S-. The Drive's power must be cycled for the setting to take
effect.
0: No Parity
1: Even Parity
2: Odd Parity
Selects the stopping method when a communication timeout fault
(CE) is detected.
0: Ramp to Stop
1: Coast to Stop
2: Fast-Stop
3: Alarm Only
Enables or disables the communications timeout fault (CE).
0: Disabled - A communication loss will not cause a
communication fault.
1: Enabled - If communication is lost for more than 2 seconds, a CE
fault will occur.
Set the delay time from when the Drive receives data to when the
Drive sends data.
Enables or disables "request to send" (RTS) control:
0: Disabled - RTS is always on
1: Enabled - RTS turns on only when sending
Selects the units used for MEMOBUS registry 0025H (monitors the
output voltage reference).
0: 0.1 V units
1: 1 V units
Pulse I/O Setup
Selects the function of pulse train terminal RP.
0: Frequency reference
1: PID feedback value
2: PID setpoint value
Sets the number of pulses (in Hz) that is equal to the maximum
output frequency E1-04.
Sets the output level when the pulse train input is at 100% as a
percentage of maximum output frequency E1-04.
Parameters A - 29
Aotewell
Email: Sales@aotewell.com
Control Method
Setting Factory
V/F
Range Setting
V/F
w/PG
0.0 to
100.0% Q Q
1000.0
–110.0 to
0.0% A A
110.0
1 to 45 3 A A
0.0 to
50.0% Q Q
1000.0
–110.0 to
0.0% A A
110.0
0 or 2 0 A A
0 or 2 0 A A
0 to 20
1F A A
Hex
0 to 4 3 A A
0 to 2 0 A A
0 to 3 3 A A
0 to 1 1 A A
5 to 65 5ms A A
0 to 1 1 A A
0, 1 0 A A
0 to 2 0 A A
1000 to
1440Hz A A
32000
0.0 to
100.0% A A
1000.0
http://www.aotewell.com
Open
Flux
Loop
Vector
Vector
Q Q
A A
A A
Q Q
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A