YASKAWA F7 User Manual page 185

http://www.aotewell.com
Parameter Parameter Name
No. Digital Operator Display
DI-08 / DI-16H2 Input
F3-01 Selection
DI Input
AO-08/AO-12 Channel 1
F4-01 Monitor Selection
AO Ch1 Sel
AO-08/AO-12 Channel 1
F4-02 Gain
AO Ch1 Gain
AO-08/AO-12 Channel 2
F4-03 Monitor Selection
AO Ch2 Sel
AO-08/AO-12 Channel 2
F4-04 Gain
AO Ch2 Gain
AO-08/AO-12 Channel 1 Out-
F4-05 put Bias
AO Ch1 Bias
AO-08/AO-12 Channel 2 Out-
F4-06 put Bias
AO Ch2 Bias
AO-12 Channel 1 Signal
F4-07 Level
AO Opt Level Ch1
AO-12 Channel 2 Signal
F4-08 Level
AO Opt Level Ch2
DO-02/DO-08 Channel 1 Out-
F5-01 put Selection
DO Ch1 Select
DO-02/DO-08 Channel 2 Out-
F5-02 put Selection
DO Ch2 Select
DO-08 Channel 3 Output
F5-03 Selection
DO Ch3 Select
DO-08 Channel 4 Output
F5-04 Selection
DO Ch4 Select
DO-08 Channel 5 Output
F5-05 Selection
DO Ch5 Select
DO-08 Channel 6 Output
F5-06 Selection
DO Ch6 Select
DO-08 Channel 7 Output
F5-07 Selection
DO Ch7 Select
Denotes that parameter can be changed when the Drive is running.
Tel: +(86) 755 8660 6182
Aotewell
Table A.1 F7 Parameter List (Continued)
Description
DI-08, 16 Setup
Sets the function of the DI-08 or the DI-16H2 digital input option
board.
0: BCD 1% unit
1: BCD 0.1% unit
2: BCD 0.01% unit
3: BCD 1Hz unit
4: BCD 0.1Hz unit
5: BCD 0.01Hz unit
6: BCD (5-digit) 0.01Hz unit (only effective when DI-16H2 is
used.)
7: Binary input
When o1-03 is set to 2 or higher, the input will be BCD, and the
units will change to the o1-03 setting.
AO-08, 12 Setup
Sets the number of the monitor item to be output. (U1-
The following settings cannot be set:
4, 10 to 14, 25, 28, 29, 30, 34, 35, 39, 40, 41.
Sets the channel 1 gain.
Ex: Set F4-02 = 50% to output 100% at 5.0V output.
Sets the number of the monitor item to be output. (U1-
The following settings cannot be set:
4, 10 to 14, 25, 28, 29, 30, 34, 39, 40, 41.
Sets the channel 2 gain.
Ex: Set F4-04 = 50% to output 100% at 5.0V output.
Sets the channel 1 bias (100%/10V).
Ex: Set F4-05 = 50% to output 0% at 5.0V output.
Sets the channel 2 bias (100%/10V).
Ex: Set F4-06 = 50% to output 0% at 5.0V output.
Sets the range of the voltage output.
0: 0 to 10Vdc
1: -10 to +10Vdc
Sets the range of the voltage output.
0: 0 to 10Vdc
1: -10 to +10Vdc
DO-02, 08 Setup
Sets the digital output function number for channel 1. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
Sets the digital output function number for channel 2. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
Sets the digital output function number for channel 3. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
Sets the digital output function number for channel 4. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
Sets the digital output function number for channel 5. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
Sets the digital output function number for channel 6. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
Sets the digital output function number for channel 7. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
Parameters A - 20
Aotewell
Email: Sales@aotewell.com
Setting Factory
Range Setting
0 to 7 0
)
1 to 45 2
0.0 to
100.0%
1000.0
)
1 to 45 3
0.0 to
50.0%
1000.0
-110.0 to
0.0%
110.0
-110.0 to
0.0%
110.0
0 to 1 0
0 to 1
0
0 to 38 0
0 to 38 1
0 to 38 2
0 to 38 4
0 to 38 6
0 to 38 37
0 to 38 F
http://www.aotewell.com
Control Method
Open
V/F Flux
V/F Loop
w/PG Vector
Vector
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A