HPE FlexNetwork HSR6800 series Configuration Manual page 97

[RouterC-GigabitEthernet3/0/2] quit
[RouterC] interface gigabitethernet 3/0/3
[RouterC-GigabitEthernet3/0/3] link-delay 0
[RouterC-GigabitEthernet3/0/3] undo stp enable
[RouterC-GigabitEthernet3/0/3] port link-type trunk
[RouterC-GigabitEthernet3/0/3] port trunk permit vlan 1 to 30
[RouterC-GigabitEthernet3/0/3] quit
# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain
1, and configure VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[RouterC] rrpp domain 1
[RouterC-rrpp-domain1] control-vlan 4092
[RouterC-rrpp-domain1] protected-vlan reference-instance 1
# Configure Router C as a transit node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.
[RouterC-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 3/0/1
secondary-port gigabitethernet 3/0/2 level 0
[RouterC-rrpp-domain1] ring 1 enable
# Configure Router C as the assistant-edge node of subring 2, with GigabitEthernet 3/0/3 as the
edge port, and enable ring 2.
[RouterC-rrpp-domain1] ring 2 node-mode assistant-edge edge-port gigabitethernet
3/0/3
[RouterC-rrpp-domain1] ring 2 enable
[RouterC-rrpp-domain1] quit
# Enable RRPP.
[RouterC] rrpp enable
4. Configure Router D:
# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region
configuration.
<RouterD> system-view
[RouterD] vlan 1 to 30
[RouterD] stp region-configuration
[RouterD-mst-region] instance 1 vlan 1 to 30
[RouterD-mst-region] active region-configuration
[RouterD-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and
GigabitEthernet 3/0/2. Disable the spanning tree feature, configure the two ports as trunk ports,
and assign them to VLANs 1 through 30.
[RouterD] interface gigabitethernet 3/0/1
[RouterD-GigabitEthernet3/0/1] link-delay 0
[RouterD-GigabitEthernet3/0/1] undo stp enable
[RouterD-GigabitEthernet3/0/1] port link-type trunk
[RouterD-GigabitEthernet3/0/1] port trunk permit vlan 1 to 30
[RouterD-GigabitEthernet3/0/1] quit
[RouterD] interface gigabitethernet 3/0/2
[RouterD-GigabitEthernet3/0/2] link-delay 0
[RouterD-GigabitEthernet3/0/2] undo stp enable
[RouterD-GigabitEthernet3/0/2] port link-type trunk
[RouterD-GigabitEthernet3/0/2] port trunk permit vlan 1 to 30
[RouterD-GigabitEthernet3/0/2] quit
90