HPE FlexNetwork HSR6800 series Configuration Manual page 113

[RouterC-GigabitEthernet3/0/3] undo stp enable
[RouterC-GigabitEthernet3/0/3] port link-type trunk
[RouterC-GigabitEthernet3/0/3] undo port trunk permit vlan 1
[RouterC-GigabitEthernet3/0/3] port trunk permit vlan 12
[RouterC-GigabitEthernet3/0/3] port trunk pvid vlan 12
[RouterC-GigabitEthernet3/0/3] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/4,
disable the spanning tree feature, and configure the port as a trunk port. Remove the port from
VLAN 1, assign it to VLAN 11, and configure VLAN 11 as its default VLAN.
[RouterC] interface gigabitethernet 3/0/4
[RouterC-GigabitEthernet3/0/4] link-delay 0
[RouterC-GigabitEthernet3/0/4] undo stp enable
[RouterC-GigabitEthernet3/0/4] port link-type trunk
[RouterC-GigabitEthernet3/0/4] undo port trunk permit vlan 1
[RouterC-GigabitEthernet3/0/4] port trunk permit vlan 11
[RouterC-GigabitEthernet3/0/4] port trunk pvid vlan 11
[RouterC-GigabitEthernet3/0/4] quit
# Create RRPP domain 1, configure VLAN 100 as the primary control VLAN of RRPP domain 1,
and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.
[RouterC] rrpp domain 1
[RouterC-rrpp-domain1] control-vlan 100
[RouterC-rrpp-domain1] protected-vlan reference-instance 1
# Configure Router C as the transit node of primary ring 1 in RRPP domain 1, with
GigabitEthernet 3/0/1 as the primary port and GigabitEthernet 3/0/2 as the secondary port, and
enable ring 1.
[RouterC-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 3/0/1
secondary-port gigabitethernet 3/0/2 level 0
[RouterC-rrpp-domain1] ring 1 enable
# Configure Router C as the edge node of subring 3 in RRPP domain 1, with GigabitEthernet
3/0/4 as the edge port, and enable subring 3.
[RouterC-rrpp-domain1] ring 3 node-mode edge edge-port gigabitethernet 3/0/4
[RouterC-rrpp-domain1] ring 3 enable
[RouterC-rrpp-domain1] quit
# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2,
and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.
[RouterC] rrpp domain 2
[RouterC-rrpp-domain2] control-vlan 105
[RouterC-rrpp-domain2] protected-vlan reference-instance 2
# Configure Router C as the transit node of primary ring 1 in RRPP domain 2, with
GigabitEthernet 3/0/1 as the primary port and GigabitEthernet 3/0/2 as the secondary port, and
enable ring 1.
[RouterC-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 3/0/1
secondary-port gigabitethernet 3/0/2 level 0
[RouterC-rrpp-domain2] ring 1 enable
# Configure Router C as the edge node of subring 2 in RRPP domain 2, with GigabitEthernet
3/0/3 as the edge port, and enable subring 2.
[RouterC-rrpp-domain2] ring 2 node-mode edge edge-port ethernet1/3
[RouterC-rrpp-domain2] ring 2 enable
[RouterC-rrpp-domain2] quit
# Enable RRPP.
106