HPE FlexNetwork HSR6800 series Configuration Manual page 36

[RouterD-GigabitEthernet3/0/3] cfd mep service-instance 1 mep 4002 enable
[RouterD-GigabitEthernet3/0/3] quit
# On Router E, configure a MEP list in service instance 1. Create and enable inward-facing
MEP 5001 in service instance 1 on GigabitEthernet 3/0/4.
[RouterE] cfd meplist 1001 4002 5001 service-instance 1
[RouterE] interface gigabitethernet 3/0/4
[RouterE-GigabitEthernet3/0/4] cfd mep 5001 service-instance 1 inbound
[RouterE-GigabitEthernet3/0/4] cfd mep service-instance 1 mep 5001 enable
[RouterE-GigabitEthernet3/0/4] quit
5. Configure MIP generation rules:
# Configure the MIP generation rule in service instance 1 on Router B as explicit.
[RouterB] cfd mip-rule explicit service-instance 1
# Configure the MIP generation rule in service instance 2 on Router C as default.
[RouterC] cfd mip-rule default service-instance 2
6. Configure CC:
# On Router A, enable the sending of CCM frames for MEP 1001 in service instance 1 on
GigabitEthernet 3/0/1.
[RouterA] interface gigabitethernet 3/0/1
[RouterA-GigabitEthernet3/0/1] cfd cc service-instance 1 mep 1001 enable
[RouterA-GigabitEthernet3/0/1] quit
# On Router B, enable the sending of CCM frames for MEP 2001 in service instance 2 on
GigabitEthernet 3/0/3.
[RouterB] interface gigabitethernet 3/0/3
[RouterB-GigabitEthernet3/0/3] cfd cc service-instance 2 mep 2001 enable
[RouterB-GigabitEthernet3/0/3] quit
# On Router D, enable the sending of CCM frames for MEP 4001 in service instance 2 on
GigabitEthernet 3/0/1. Enable the sending of CCM frames for MEP 4002 in service instance 1
on GigabitEthernet 3/0/3.
[RouterD] interface gigabitethernet 3/0/1
[RouterD-GigabitEthernet3/0/1] cfd cc service-instance 2 mep 4001 enable
[RouterD-GigabitEthernet3/0/1] quit
[RouterD] interface gigabitethernet 3/0/3
[RouterD-GigabitEthernet3/0/3] cfd cc service-instance 1 mep 4002 enable
[RouterD-GigabitEthernet3/0/3] quit
# On Router E, enable the sending of CCM frames for MEP 5001 in service instance 1 on
GigabitEthernet 3/0/4.
[RouterE] interface gigabitethernet 3/0/4
[RouterE-GigabitEthernet3/0/4] cfd cc service-instance 1 mep 5001 enable
[RouterE-GigabitEthernet3/0/4] quit
Verifying the configuration
1. Verify the LB function:
When the CC function detects a link fault, use the LB function to locate the fault.
# Enable LB on Router A to check the status of the link between MEP 1001 and MEP 5001 in
service instance 1.
[RouterA] cfd loopback service-instance 1 mep 1001 target-mep 5001
Loopback to 0010-FC00-6515 with the sequence number start from 1001-43404:
Reply from 0010-FC00-6515: sequence number=1001-43404 time=5ms
Reply from 0010-FC00-6515: sequence number=1001-43405 time=5ms
29