HPE FlexNetwork HSR6800 series Configuration Manual page 115

# Configure Router D as the transit node of primary ring 1 in RRPP domain 2, with
GigabitEthernet 3/0/1 as the primary port and GigabitEthernet 3/0/2 as the secondary port, and
enable ring 1.
[RouterD-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 3/0/1
secondary-port gigabitethernet 3/0/2 level 0
[RouterD-rrpp-domain2] ring 1 enable
[RouterD-rrpp-domain2] quit
# Enable RRPP.
[RouterD] rrpp enable
5. Configure Router E:
# Create VLAN 12, map VLAN 12 to MSTI 2, and activate MST region configuration.
<RouterE> system-view
[RouterE] vlan 12
[RouterE-vlan12] quit
[RouterE] stp region-configuration
[RouterE-mst-region] instance 2 vlan 12
[RouterE-mst-region] active region-configuration
[RouterE-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and
GigabitEthernet 3/0/2, disable the spanning tree feature, and configure the two ports as trunk
ports. Remove the two ports from VLAN 1, assign them to VLAN 12, and configure VLAN 12 as
their default VLAN.
[RouterE] interface gigabitethernet 3/0/1
[RouterE-GigabitEthernet3/0/1] link-delay 0
[RouterE-GigabitEthernet3/0/1] undo stp enable
[RouterE-GigabitEthernet3/0/1] port link-type trunk
[RouterE-GigabitEthernet3/0/1] undo port trunk permit vlan 1
[RouterE-GigabitEthernet3/0/1] port trunk permit vlan 12
[RouterE-GigabitEthernet3/0/1] port trunk pvid vlan 12
[RouterE-GigabitEthernet3/0/1] quit
[RouterE] interface gigabitethernet 3/0/2
[RouterE-GigabitEthernet3/0/2] link-delay 0
[RouterE-GigabitEthernet3/0/2] undo stp enable
[RouterE-GigabitEthernet3/0/2] port link-type trunk
[RouterE-GigabitEthernet3/0/2] undo port trunk permit vlan 1
[RouterE-GigabitEthernet3/0/2] port trunk permit vlan 12
[RouterE-GigabitEthernet3/0/2] port trunk pvid vlan 12
[RouterE-GigabitEthernet3/0/2] quit
# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN, and configure the
VLAN mapped to MSTI 2 as the protected VLAN.
[RouterE] rrpp domain 2
[RouterE-rrpp-domain2] control-vlan 105
[RouterE-rrpp-domain2] protected-vlan reference-instance 2
# Configure Router E as the master mode of subring 2 in RRPP domain 2, with GigabitEthernet
3/0/2 as the primary port and GigabitEthernet 3/0/1 as the secondary port, and enable ring 2.
[RouterE-rrpp-domain2] ring 2 node-mode master primary-port gigabitethernet 3/0/2
secondary-port gigabitethernet 3/0/1 level 1
[RouterE-rrpp-domain2] ring 2 enable
[RouterE-rrpp-domain2] quit
108