HPE FlexNetwork HSR6800 series Configuration Manual page 112

[RouterB-rrpp-domain2] protected-vlan reference-instance 2
# Configure Router B as the transit node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.
[RouterB-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 3/0/1
secondary-port gigabitethernet 3/0/2 level 0
[RouterB-rrpp-domain2] ring 1 enable
# Configure Router B as the assistant-edge node of subring 2 in RRPP domain 2, with
GigabitEthernet 3/0/3 as the edge port, and enable subring 2.
[RouterB-rrpp-domain2] ring 2 node-mode assistant-edge edge-port gigabitethernet
3/0/3
[RouterB-rrpp-domain2] ring 2 enable
[RouterC-rrpp-domain2] quit
# Enable RRPP.
[RouterB] rrpp enable
3. Configure Router C:
# Create VLANs 11 and 12, map VLAN 11 to MSTI 1 and VLAN 12 to MSTI 2, and activate MST
region configuration.
<RouterC> system-view
[RouterC] vlan 11 to 12
[RouterC] stp region-configuration
[RouterC-mst-region] instance 1 vlan 11
[RouterC-mst-region] instance 2 vlan 12
[RouterC-mst-region] active region-configuration
[RouterC-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and
GigabitEthernet 3/0/2, disable the spanning tree feature, and configure the two ports as trunk
ports. Remove the two ports from VLAN 1, assign them to VLANs 11 and 12, and configure
VLAN 11 as their default VLAN.
[RouterC] interface gigabitethernet 3/0/1
[RouterC-GigabitEthernet3/0/1] link-delay 0
[RouterC-GigabitEthernet3/0/1] undo stp enable
[RouterC-GigabitEthernet3/0/1] port link-type trunk
[RouterC-GigabitEthernet3/0/1] undo port trunk permit vlan 1
[RouterC-GigabitEthernet3/0/1] port trunk permit vlan 11 12
[RouterC-GigabitEthernet3/0/1] port trunk pvid vlan 11
[RouterC-GigabitEthernet3/0/1] quit
[RouterC] interface gigabitethernet 3/0/2
[RouterC-GigabitEthernet3/0/2] link-delay 0
[RouterC-GigabitEthernet3/0/2] undo stp enable
[RouterC-GigabitEthernet3/0/2] port link-type trunk
[RouterC-GigabitEthernet3/0/2] undo port trunk permit vlan 1
[RouterC-GigabitEthernet3/0/2] port trunk permit vlan 11 12
[RouterC-GigabitEthernet3/0/2] port trunk pvid vlan 11
[RouterC-GigabitEthernet3/0/2] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/3,
disable the spanning tree feature, and configure the port as a trunk port. Remove the port from
VLAN 1, assign it to VLAN 12, and configure VLAN 12 as its default VLAN.
[RouterC] interface gigabitethernet 3/0/3
[RouterC-GigabitEthernet3/0/3] link-delay 0
105