HPE FlexNetwork HSR6800 series Configuration Manual page 128

[RouterD-GigabitEthernet3/0/1] undo shutdown
[RouterD-GigabitEthernet3/0/1] quit
[RouterD] interface gigabitethernet 3/0/2
[RouterD-GigabitEthernet3/0/2] undo shutdown
[RouterD-GigabitEthernet3/0/2] quit
3. Configure Router B:
# Create VLANs 1 through 30.
<RouterB> system-view
[RouterB] vlan 1 to 30
# Configure GigabitEthernet 3/0/1 as a trunk port, and assign it to VLANs 1 through 30. Enable
flush message receiving on it, and configure VLAN 10 and VLAN 20 as the receive control
VLANs.
[RouterB] interface gigabitethernet 3/0/1
[RouterB-GigabitEthernet3/0/1] port link-type trunk
[RouterB-GigabitEthernet3/0/1] port trunk permit vlan 1 to 30
[RouterB-GigabitEthernet3/0/1] smart-link flush enable control-vlan 10 20
[RouterB-GigabitEthernet3/0/1] quit
# Configure GigabitEthernet 3/0/2 as a trunk port, and assign it to VLANs 1 through 30. Disable
the spanning tree feature and enable flush message receiving on it, and configure VLAN 20 as
the receive control VLAN.
[RouterB] interface gigabitethernet 3/0/2
[RouterB-GigabitEthernet3/0/2] port link-type trunk
[RouterB-GigabitEthernet3/0/2] port trunk permit vlan 1 to 30
[RouterB-GigabitEthernet3/0/2] undo stp enable
[RouterB-GigabitEthernet3/0/2] smart-link flush enable control-vlan 20
[RouterB-GigabitEthernet3/0/2] quit
# Configure GigabitEthernet 3/0/3 as a trunk port, and assign it to VLANs 1 through 30. Disable
the spanning tree feature and enable flush message receiving on it, and configure VLAN 10 as
the receive control VLAN.
[RouterB] interface gigabitethernet 3/0/3
[RouterB-GigabitEthernet3/0/3] port link-type trunk
[RouterB-GigabitEthernet3/0/3] port trunk permit vlan 1 to 30
[RouterB-GigabitEthernet3/0/3] undo stp enable
[RouterB-GigabitEthernet3/0/3] smart-link flush enable control-vlan 10
[RouterB-GigabitEthernet3/0/3] quit
4. Configure Router E:
# Create VLANs 1 through 30.
<RouterE> system-view
[RouterE] vlan 1 to 30
# Configure GigabitEthernet 3/0/1 as a trunk port, and assign it to VLANs 1 through 30. Enable
flush message receiving on it, and configure VLAN 10 and VLAN 20 as the receive control
VLANs.
[RouterE] interface gigabitethernet 3/0/1
[RouterE-GigabitEthernet3/0/1] port link-type trunk
[RouterE-GigabitEthernet3/0/1] port trunk permit vlan 1 to 30
[RouterE-GigabitEthernet3/0/1] smart-link flush enable control-vlan 10 20
[RouterE-GigabitEthernet3/0/1] quit
121