HPE FlexNetwork HSR6800 series Configuration Manual page 132

# Configure GigabitEthernet 3/0/1 as a trunk port, assign it to VLANs 1 through 200, enable
flush message receiving, and configure VLAN 10 and VLAN 110 as the receive control VLANs
on the port.
[RouterB] interface gigabitethernet 3/0/1
[RouterB-GigabitEthernet3/0/1] port link-type trunk
[RouterB-GigabitEthernet3/0/1] port trunk permit vlan 1 to 200
[RouterB-GigabitEthernet3/0/1] smart-link flush enable control-vlan 10 110
[RouterB-GigabitEthernet3/0/1] quit
# Configure GigabitEthernet 3/0/2 as a trunk port, assign it to VLANs 1 through 200, disable the
spanning tree feature and enable flush message receiving on it, and configure VLAN 10 and
VLAN 110 as the receive control VLANs.
[RouterB] interface gigabitethernet 3/0/2
[RouterB-GigabitEthernet3/0/2] port link-type trunk
[RouterB-GigabitEthernet3/0/2] port trunk permit vlan 1 to 200
[RouterB-GigabitEthernet3/0/2] undo stp enable
[RouterB-GigabitEthernet3/0/2] smart-link flush enable control-vlan 10 110
[RouterB-GigabitEthernet3/0/2] quit
3. Configure Router D:
# Create VLAN 1 through VLAN 200.
<RouterD> system-view
[RouterD] vlan 1 to 200
# Configure GigabitEthernet 3/0/1 as a trunk port, assign it to VLANs 1 through 200, enable
flush message receiving, and configure VLAN 10 and VLAN 110 as the receive control VLANs
on the port.
[RouterD] interface gigabitethernet 3/0/1
[RouterD-GigabitEthernet3/0/1] port link-type trunk
[RouterD-GigabitEthernet3/0/1] port trunk permit vlan 1 to 200
[RouterD-GigabitEthernet3/0/1] smart-link flush enable control-vlan 10 110
[RouterD-GigabitEthernet3/0/1] quit
# Configure GigabitEthernet 3/0/2 as a trunk port and assign it to VLANs 1 through 200, disable
the spanning tree feature and enable flush message receiving, and configure VLAN 10 and
VLAN 110 as the receive control VLANs on the port.
[RouterD] interface gigabitethernet 3/0/2
[RouterD-GigabitEthernet3/0/2] port link-type trunk
[RouterD-GigabitEthernet3/0/2] port trunk permit vlan 1 to 200
[RouterD-GigabitEthernet3/0/2] undo stp enable
[RouterD-GigabitEthernet3/0/2] smart-link flush enable control-vlan 10 110
[RouterD-GigabitEthernet3/0/2] quit
4. Configure Router A:
# Create VLAN 1 through VLAN 200.
<RouterA> system-view
[RouterA] vlan 1 to 200
# Configure GigabitEthernet 3/0/1 and GigabitEthernet 3/0/2 as trunk ports, assign them to
VLANs 1 through 200, enable flush message receiving, and configure VLAN 10 and VLAN 110
as the receive control VLANs on the ports.
[RouterA] interface gigabitethernet 3/0/1
[RouterA-GigabitEthernet3/0/1] port link-type trunk
[RouterA-GigabitEthernet3/0/1] port trunk permit vlan 1 to 200
[RouterA-GigabitEthernet3/0/1] smart-link flush enable control-vlan 10 110
125