HPE FlexNetwork HSR6800 series Configuration Manual page 103

# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1
through GigabitEthernet 3/0/4. Disable the spanning tree feature, configure the four ports as
trunk ports, and assign them to VLANs 1 through 30.
[RouterC] interface gigabitethernet 3/0/1
[RouterC-GigabitEthernet3/0/1] link-delay 0
[RouterC-GigabitEthernet3/0/1] undo stp enable
[RouterC-GigabitEthernet3/0/1] port link-type trunk
[RouterC-GigabitEthernet3/0/1] port trunk permit vlan 1 to 30
[RouterC-GigabitEthernet3/0/1] quit
[RouterC] interface gigabitethernet 3/0/2
[RouterC-GigabitEthernet3/0/2] link-delay 0
[RouterC-GigabitEthernet3/0/2] undo stp enable
[RouterC-GigabitEthernet3/0/2] port link-type trunk
[RouterC-GigabitEthernet3/0/2] port trunk permit vlan 1 to 30
[RouterC-GigabitEthernet3/0/2] quit
[RouterC] interface gigabitethernet 3/0/3
[RouterC-GigabitEthernet3/0/3] link-delay 0
[RouterC-GigabitEthernet3/0/3] undo stp enable
[RouterC-GigabitEthernet3/0/3] port link-type trunk
[RouterC-GigabitEthernet3/0/3] port trunk permit vlan 1 to 30
[RouterC-GigabitEthernet3/0/3] quit
[RouterC] interface gigabitethernet 3/0/4
[RouterC-GigabitEthernet3/0/4] link-delay 0
[RouterC-GigabitEthernet3/0/4] undo stp enable
[RouterC-GigabitEthernet3/0/4] port link-type trunk
[RouterC-GigabitEthernet3/0/4] port trunk permit vlan 1 to 30
[RouterC-GigabitEthernet3/0/4] quit
# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain
1, and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[RouterC] rrpp domain 1
[RouterC-rrpp-domain1] control-vlan 4092
[RouterC-rrpp-domain1] protected-vlan reference-instance 1
# Configure Router C as the transit node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.
[RouterC-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 3/0/1
secondary-port gigabitethernet 3/0/2 level 0
[RouterC-rrpp-domain1] ring 1 enable
# Configure Router C as the assistant-edge node of subring 4, with GigabitEthernet 3/0/3 as the
edge port, and enable subring 4.
[RouterC-rrpp-domain1] ring 4 node-mode assistant-edge edge-port gigabitethernet
3/0/3
[RouterC-rrpp-domain1] ring 4 enable
# Configure Router C as the assistant-edge node of subring 5, with GigabitEthernet 3/0/4 as the
edge port, and enable subring 5.
[RouterC-rrpp-domain1] ring 5 node-mode assistant-edge edge-port gigabitethernet
3/0/4
[RouterC-rrpp-domain1] ring 5 enable
[RouterC-rrpp-domain1] quit
# Enable RRPP.
96