Table of Contents
Advertisement
Manual Transmission
Mainshaft Thrust Clearance Adjustment (cont'd)
72mmShim
Part Number
A
23931-P21-000
B
23932-P21-000
e
23933-P21-000
.-
D
23934-P21-000
E '
23935-P21-000
F
23936-P21-000
G
23937 -P21-000
H
23938-P21-000
I
23939-P21-000
J
23940-P21-000
K
23941-P21-000
L
23942-P21-000
r#-.
23943-P21-000
N
23944-P21-000
a
23945-P21-000
P
23946-P21-000
Q
23947 -P21-000
R
23948-P21-000
S
23949-P21-000
T
23950-P21-000
U
23951-P21-000
V
23952-P21-000
W'
23953-P21-000
X
23954-P21-000
y
23955-P21-000
Z
23956-P21-000
AA
23957 -P21-000
AB
23958-P21-000
Ae
23959-P21-000
AD
23960-P21-000
AE
23961-P21-000
AF
23962-P21-000
AG
23963-P21-000
AH
23964-P21-000
AI
23965-P21-000
AJ
23966-P21-000
AK
23967 -P21-000
AL
23968-P21-000
AM
23969-P21-000
AN
23970-P21-000
AO
23971-P21-000
13-44
Thickness
0.60 mm (0.0236 in.1
0.63 mm (0.0248 in.1
0.66 mm (0.0260 in.1
0.69 mm (0.0271 in.1
0.72 mm (0.0283 in.1
0.75 mm (0.0295 in.1
0.78 mm (0.0307 in.1
0.81 mm (0.0319 in,1
0.84 mm (0.0331 in.1
0.87 mm (0.0343 in,1
0.90 mm (0.0354 in.1
0.93 mm (0,0366 in.1
,
0.96 mm (0.0378 i.nl
0.99 mm (0.0390 in. I
1.02 mm (0.0402 in.1
1.05 mm (0.0413 in.1
1.08 mm (0.0425 in.1
,
1.11 mm (0.0437 in.1
1.14 mm (0.0449 in. I
1.17 mm (0.0461 in.1
1.20 mm (0.0472 in.1
1.23 mm (0.0484 in.1
1.26 mm (0.0496 in. I
1.29 mm (0.0508 in.1
1.32 mm (0.0520 in.1
1.35 mm (0.0531 in.1
1.38 mm (0.0543 in,1
1.41 mm (0.0555 in,1
1.44 mm (0.0567 in.1
1.47 mm (0.0579 in.1
1.50 mm (0.0591 in.1
1.53 mm (0.0602 in.1
1.56 mm (0,0614 in.1
1.59 mm (0.0626 in,1
1.62 mm (0,0638 in.1
1.65 mm (0.0650 in,1
1.68 mm (0.0661 in. I
1.71 mm (0.0673 in.1
1.74 mm (0.0685 in.1
1.77 mm
(0.0697.Ln.L
1.80 mm (0.0709 in.1
7. Install the 72 mm shim (AI selected and oil guide
plate M in the transmission housing (BI.
8. Thoroughly clean the spring washer (AI and
washer (BI before installing them on the clutch
housing side ball bearing (el. Note the installation
direction of the spring washer.
C~D/B
~
~A
--- -+-------
....
~-:--_-----I-----_--,:,
....
---------~----------
- - -------- -------------
.
~>=r--:::
. . . . .
. . . .
~
9. Install the mainshaft in the clutch housing.
10. Place the transmission housing over the mainshaft
and onto the clutch housing,
11. Tighten the clutch and transmission housings with
several 8 mm bolts,
NOTE: It is not necessary to use sealing agent
between the housings.
12. Tap the mains haft with a plastic hammer.
•
Advertisement
Table of Contents
Troubleshooting
