Huawei quidway s7700 Configuration Manual page 369

Quidway S7700 Smart Routing Switch
Configuration Guide - SPU
[S7700] set service-type 1
The serivce type will be availble after you restart the board, please restart!
Step 3 Configure interfaces of the LPUs.
# Log in to MPU A and MPU B to create VLAN 10, VLAN 11, and VLAN 13, bind GE 2/0/10
on LPU A and GE 2/0/11 on LPU B to Eth-Trunk 1 and Eth-Trunk 2 respectively, and bind XGE
3/0/0 on MPU A and XGE 3/0/1 on MPU B to Eth-Trunk 0.
[MPU] vlan 10
[MPU-VLAN10] quit
[MPU] vlan 11
[MPU-VLAN11] quit
[MPU] vlan 13
[MPU-VLAN13] quit
[MPU] vlan 18
[MPU-VLAN18] quit
[MPU] interface eth-trunk0
[MPU-Eth-Trunk0] port link-type trunk
[MPU-Eth-Trunk0] port trunk allow-pass vlan 10 to 11
[MPU-Eth-Trunk0] port trunk allow-pass vlan 13
[MPU-Eth-Trunk0] undo port trunk allow-pass vlan 1
[MPU-Eth-Trunk0] quit
[MPU] interface eth-trunk1
[MPU-Eth-Trunk1] port link-type trunk
[MPU-Eth-Trunk1] port trunk allow-pass vlan 10
[MPU-Eth-Trunk1] undo port trunk allow-pass vlan 1
[MPU-Eth-Trunk1] quit
[MPU] interface eth-trunk2
[MPU-Eth-Trunk2] port link-type trunk
[MPU-Eth-Trunk2] port trunk allow-pass vlan 11
[MPU-Eth-Trunk2] undo port trunk allow-pass vlan 1
[MPU-Eth-Trunk2] quit
[MPU] interface gigabitethernet 2/0/10
[MPU-GigabitEthernet2/0/10] eth-trunk 1
[MPU-GigabitEthernet2/0/10] quit
[MPU] interface gigabitethernet 2/0/11
[MPU-GigabitEthernet2/0/11] eth-trunk 2
[MPU-GigabitEthernet2/0/11] quit
[MPU] interface xgigabitethernet 3/0/0
[MPU-XGigabitEthernet3/0/0] eth-trunk 0
[MPU-XGigabitEthernet3/0/0] quit
[MPU] interface xgigabitethernet 3/0/1
[MPU-XGigabitEthernet3/0/1] eth-trunk 0
[MPU-XGigabitEthernet3/0/1] quit
Step 4 Configure a TCP link.
# Log in to MPU A and MPU B to configure interfaces GE 2/0/13 as interfaces of the TCP link.
[MPU] interface gigabitethernet 2/0/13
[MPU-GigabitEthernet2/0/13] port link-type trunk
[MPU-GigabitEthernet2/0/13] port trunk allow-pass vlan 13
[MPU-GigabitEthernet2/0/13] undo port trunk allow-pass vlan 1
[MPU-GigabitEthernet2/0/13] quit
Step 5 Configure interfaces of SPUs.
# Log in to SPU A and SPU B to create Eth-Trunk 0 and bind XGE 0/0/1 and XGE 0/0/2 to Eth-
Trunk 0.
[S7700] interface eth-trunk0
[S7700-Eth-Trunk0] quit
[S7700] interface xgigabitethernet 0/0/1
Issue 01 (2011-07-15)
NOTE
By default, GE 2/0/10, GE 2/0/11, GE 2/0/13, XGE 3/0/0, and XGE 3/0/1 allow packets of VLAN 1 to
pass through.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7 Dual-System HSB Configuration
358