Huawei quidway s7700 Configuration Manual page 339

Quidway S7700 Smart Routing Switch
Configuration Guide - SPU
Issue 01 (2011-07-15)
[SwitchB] interface Eth-Trunk 0
[SwitchB-Eth-Trunk0] port link-type trunk
[SwitchB-Eth-Trunk0] port trunk allow-pass vlan 600 800
[SwitchB-Eth-Trunk0] quit
[SwitchB] interface GigabitEthernet4/0/6
[SwitchB-GigabitEthernet4/0/6] port link-type trunk
[SwitchB-GigabitEthernet4/0/6] undo port trunk allow-pass vlan 1
[SwitchB-GigabitEthernet4/0/6] port trunk allow-pass vlan 600
[SwitchB-GigabitEthernet4/0/6] quit
[SwitchB] interface GigabitEthernet4/0/2
[SwitchB-GigabitEthernet4/0/2] port link-type trunk
[SwitchB-GigabitEthernet4/0/2] undo port trunk allow-pass vlan 1
[SwitchB-GigabitEthernet4/0/2] port trunk allow-pass vlan 800
[SwitchB-GigabitEthernet4/0/2] quit
[SwitchB] interface XGigabitEthernet8/0/0
[SwitchB-XGigabitEthernet8/0/0] eth-Trunk 0
[SwitchB-XGigabitEthernet8/0/0] quit
[SwitchB] interface XGigabitEthernet8/0/1
[SwitchB-XGigabitEthernet8/0/1] eth-Trunk 0
[SwitchB-XGigabitEthernet8/0/1] quit
(2) Import traffic from SwitchB to SPUB, that is, FWB. SPUB is installed in slot 11.
[SwitchB] vlan batch 700 900
[SwitchB] interface Eth-Trunk 1
[SwitchB-Eth-Trunk1] port link-type trunk
[SwitchB-Eth-Trunk1] port trunk allow-pass vlan 700 900
[SwitchB-Eth-Trunk1] quit
[SwitchB] interface GigabitEthernet4/0/7
[SwitchB-GigabitEthernet4/0/7] port link-type trunk
[SwitchB-GigabitEthernet4/0/7] undo port trunk allow-pass vlan 1
[SwitchB-GigabitEthernet4/0/7] port trunk allow-pass vlan 700
[SwitchB-GigabitEthernet4/0/7] quit
[SwitchB] interface GigabitEthernet4/0/3
[SwitchB-GigabitEthernet4/0/3] port link-type trunk
[SwitchB-GigabitEthernet4/0/3] undo port trunk allow-pass vlan 1
[SwitchB-GigabitEthernet4/0/3] port trunk allow-pass vlan 900
[SwitchB-GigabitEthernet4/0/3] quit
[SwitchB] interface XGigabitEthernet11/0/0
[SwitchB-XGigabitEthernet11/0/0] eth-Trunk 1
[SwitchB-XGigabitEthernet11/0/0] quit
[SwitchB] interface XGigabitEthernet11/0/1
[SwitchB-XGigabitEthernet11/0/1] eth-Trunk 1
[SwitchB-XGigabitEthernet11/0/1] quit
(3) Add inbound and outbound interfaces to the VLAN on SPUA and configure static
routes to import traffic to the SPU of SwitchC.
<Quidway> system-view
[Quidway] sysname SPUA
[SPUA] interface Eth-Trunk 0
[SPUA-Eth-Trunk0] quit
[SPUA] interface Eth-Trunk0.5
[SPUA-Eth-Trunk0.5] control-vid 600 dot1q-termination
[SPUA-Eth-Trunk0.5] dot1q termination vid 600
[SPUA-Eth-Trunk0.5] ip address 7.7.61.2 255.255.255.0
[SPUA-Eth-Trunk0.5] arp broadcast enable
[SPUA-Eth-Trunk0.5] quit
[SPUA] interface Eth-Trunk0.6
[SPUA-Eth-Trunk0.6] control-vid 800 dot1q-termination
[SPUA-Eth-Trunk0.6] dot1q termination vid 800
[SPUA-Eth-Trunk0.6] ip address 11.11.61.1 255.255.255.0
[SPUA-Eth-Trunk0.6] arp broadcast enable
[SPUA-Eth-Trunk0.6] quit
[SPUA] interface XGigabitEthernet0/0/1
[SPUA-XGigabitEthernet0/0/1] eth-Trunk 0
[SPUA-XGigabitEthernet0/0/1] quit
[SPUA] interface XGigabitEthernet0/0/2
[SPUA-XGigabitEthernet0/0/2] eth-Trunk 0
[SPUA-XGigabitEthernet0/0/2] quit
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 Load Balancing Configuration
328