Huawei quidway s7700 Configuration Manual page 359

Quidway S7700 Smart Routing Switch
Configuration Guide - SPU
[MPU] interface gigabitethernet 2/0/10
[MPU-GigabitEthernet2/0/10] port link-type trunk
[MPU-GigabitEthernet2/0/10] port trunk allow-pass vlan 18
[MPU-GigabitEthernet2/0/10] undo port trunk allow-pass vlan 1
[MPU-GigabitEthernet2/0/10] quit
[MPU] interface gigabitethernet 2/0/11
[MPU-GigabitEthernet2/0/11] port link-type trunk
[MPU-GigabitEthernet2/0/11] port trunk allow-pass vlan 11
[MPU-GigabitEthernet2/0/11] undo port trunk allow-pass vlan 1
[MPU-GigabitEthernet2/0/11] quit
[MPU] interface vlanif 10
[MPU-VLANIF10] ip address 10.0.0.9 24
[MPU-VLANIF10] quit
[MPU] interface eth-trunk0
[MPU-Eth-Trunk0] port link-type trunk
[MPU-Eth-Trunk0] port trunk allow-pass vlan 10 to 11
[MPU-Eth-Trunk0] port trunk allow-pass vlan 13
[MPU-Eth-Trunk0] undo port trunk allow-pass vlan 1
[MPU-Eth-Trunk0] quit
[MPU] interface eth-trunk1
[MPU-Eth-Trunk1] port link-type trunk
[MPU-Eth-Trunk1] port trunk allow-pass vlan 10 to 11
[MPU-Eth-Trunk1] port trunk allow-pass vlan 13
[MPU-Eth-Trunk1] undo port trunk allow-pass vlan 1
[MPU-Eth-Trunk1] quit
[MPU] interface xgigabitethernet 3/0/0
[MPU-XGigabitEthernet3/0/0] eth-trunk 0
[MPU-XGigabitEthernet3/0/0] quit
[MPU] interface xgigabitethernet 3/0/1
[MPU-XGigabitEthernet3/0/1] eth-trunk 0
[MPU-XGigabitEthernet3/0/1] quit
[MPU] interface xgigabitethernet 5/0/0
[MPU-XGigabitEthernet5/0/0] eth-trunk 1
[MPU-XGigabitEthernet5/0/0] quit
[MPU] interface xgigabitethernet 5/0/1
[MPU-XGigabitEthernet5/0/1] eth-trunk 1
[MPU-XGigabitEthernet5/0/1] quit
Step 3 Configure a static route on the MPU.
# Log in to the MPU to configure a static route.
[MPU] ip route-static 11.0.0.9 255.0.0.0 vlanif10 10.0.0.1
Step 4 Configure interfaces of SPUs.
# Log in to SPU A and SPU B to create Eth-Trunk 0 and bind XGE 0/0/1 and XGE 0/0/2 to Eth-
Trunk 0.
[S7700] interface eth-trunk0
[S7700-Eth-Trunk0] quit
[S7700] interface xgigabitethernet 0/0/1
[S7700-XGigabitEthernet0/0/1] eth-trunk 0
[S7700-XGigabitEthernet0/0/1] quit
[S7700] interface xgigabitethernet 0/0/2
[S7700-XGigabitEthernet0/0/2] eth-trunk 0
[S7700-XGigabitEthernet0/0/2] quit
Step 5 Configure VRRP.
# Log in to SPU A.
l Set the IP address of Eth-Trunk 0.1 to 10.0.0.2/24, add Eth-Trunk 0.1 to VRRP backup group
Issue 01 (2011-07-15)
10, set the virtual IP address of VRRP backup group 10 to 10.0.0.1/24, and set the priority
of VRRP backup group 10 to 120.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7 Dual-System HSB Configuration
348