Huawei quidway s7700 Configuration Manual page 301

Quidway S7700 Smart Routing Switch
Configuration Guide - SPU
Data Preparation
To complete the configuration, you need the following data:
l
l
l
l
l
l
l
l
Procedure
Step 1 Configure traffic importing on the Switch.
1.
2.
Issue 01 (2011-07-15)
Network segment and index of the NAT address pool
Server names, connection quantity limits, connection rate limits, and bandwidth rate limits
Name and related parameters of the probe
Server group name, load balancing algorithm, and forwarding mode
Name and matching rule of the Layer 7 classifier
Load balancing action profile name, action, and master and backup server groups
Name of the Layer 3 classifier and ACL and Layer 7 classifier bound to the Layer 3 classifier
Name of the load balancing policy and interface where the load balancing policy is applied
Import traffic to the SPU on the Switch.
<Switch> system-view
[Switch] vlan batch 12 to 16
[Switch] interface gigabitethernet 3/0/0
[Switch-GigabitEthernet3/0/0] port link-type trunk
[Switch-GigabitEthernet3/0/0] port trunk allow-pass vlan 12
[Switch-GigabitEthernet3/0/0] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/0] quit
[Switch] interface gigabitethernet 3/0/1
[Switch-GigabitEthernet3/0/1] port link-type trunk
[Switch-GigabitEthernet3/0/1] port trunk allow-pass vlan 13
[Switch-GigabitEthernet3/0/1] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/1] quit
[Switch] interface gigabitethernet 3/0/2
[Switch-GigabitEthernet3/0/2] port link-type trunk
[Switch-GigabitEthernet3/0/2] port trunk allow-pass vlan 14
[Switch-GigabitEthernet3/0/2] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/2] quit
[Switch] interface gigabitethernet 3/0/3
[Switch-GigabitEthernet3/0/3] port link-type trunk
[Switch-GigabitEthernet3/0/3] port trunk allow-pass vlan 15
[Switch-GigabitEthernet3/0/3] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/3] quit
[Switch] interface gigabitethernet 3/0/4
[Switch-GigabitEthernet3/0/4] port link-type trunk
[Switch-GigabitEthernet3/0/4] port trunk allow-pass vlan 16
[Switch-GigabitEthernet3/0/4] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/4] quit
[Switch] interface eth-trunk 0
[Switch-Eth-Trunk0] port link-type trunk
[Switch-Eth-Trunk0] port trunk allow-pass vlan 12 to 16
[Switch-Eth-Trunk0] undo port trunk allow-pass vlan 1
[Switch-Eth-Trunk0] quit
[Switch] interface xgigabitethernet5/0/0
[Switch-XGigabitEthernet5/0/0] eth-trunk 0
[Switch-XGigabitEthernet5/0/0] quit
[Switch] interface xgigabitethernet5/0/1
[Switch-XGigabitEthernet5/0/1] eth-trunk 0
[Switch-XGigabitEthernet5/0/1] quit
Add an interface to a VLAN on the Switch, and configure an NAT address pool.
<Quidway> system-view
[Quidway] sysname SPU
[SPU] nat address-group 2 100.100.100.2 100.100.100.200
[SPU] interface eth-trunk 0
[SPU-Eth-Trunk0] quit
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 Load Balancing Configuration
290