Huawei quidway s7700 Configuration Manual page 341

Quidway S7700 Smart Routing Switch
Configuration Guide - SPU
l
Issue 01 (2011-07-15)
[SPUB] interface Eth-Trunk 0.5
[SPUB-Eth-Trunk0.5] zone a
[SPUB-Eth-Trunk0.5] quit
[SPUB] interface Eth-Trunk 0.6
[SPUB-Eth-Trunk0.6] zone b
[SPUB-Eth-Trunk0.6] quit
Configure SwitchC.
1. Configure traffic importing on SwitchC.
(1) Import traffic from SwitchC to the SPU. The SPU is installed in slot 2.
<Quidway> system-view
[Quidway] sysname SwitchC
[SwitchC] vlan batch 800 900 1000
[SwitchC] interface Eth-Trunk 1
[SwitchC-Eth-Trunk1] port link-type trunk
[SwitchC-Eth-Trunk1] port trunk allow-pass vlan 800 900 1000
[SwitchC-Eth-Trunk1] quit
[SwitchC] interface GigabitEthernet1/0/22
[SwitchC-GigabitEthernet1/0/22] port link-type trunk
[SwitchC-GigabitEthernet1/0/22] undo port trunk allow-pass vlan 1
[SwitchC-GigabitEthernet1/0/22] port trunk allow-pass vlan 800
[SwitchC-GigabitEthernet1/0/22] quit
[SwitchC] interface GigabitEthernet1/0/23
[SwitchC-GigabitEthernet1/0/23] port link-type trunk
[SwitchC-GigabitEthernet1/0/23] undo port trunk allow-pass vlan 1
[SwitchC-GigabitEthernet1/0/23] port trunk allow-pass vlan 900
[SwitchC-GigabitEthernet1/0/23] quit
[SwitchC] interface GigabitEthernet1/0/28
[SwitchC-GigabitEthernet1/0/28] port link-type trunk
[SwitchC-GigabitEthernet1/0/28] undo port trunk allow-pass vlan 1
[SwitchC-GigabitEthernet1/0/28] port trunk allow-pass vlan 1000
[SwitchC-GigabitEthernet1/0/28] quit
[SwitchC] interface XGigabitEthernet2/0/0
[SwitchC-XGigabitEthernet2/0/0] eth-Trunk 1
[SwitchC-XGigabitEthernet2/0/0] quit
[SwitchC] interface XGigabitEthernet2/0/1
[SwitchC-XGigabitEthernet2/0/1] eth-Trunk 1
[SwitchC-XGigabitEthernet2/0/1] quit
(2) Add inbound and outbound interfaces to a VLAN on the SPU.
<Quidway> system-view
[Quidway] sysname SPU
[SPU] interface Eth-Trunk 0
[SPU-Eth-Trunk0] quit
[SPU] interface Eth-Trunk 0.8
[SPU-Eth-Trunk0.8] control-vid 800 dot1q-termination
[SPU-Eth-Trunk0.8] dot1q termination vid 800
[SPU-Eth-Trunk0.8] ip address 11.11.61.2 255.255.255.0
[SPU-Eth-Trunk0.8] arp broadcast enable
[SPU-Eth-Trunk0.8] quit
[SPU] interface Eth-Trunk 0.9
[SPU-Eth-Trunk0.9] control-vid 900 dot1q-termination
[SPU-Eth-Trunk0.9] dot1q termination vid 900
[SPU-Eth-Trunk0.9] ip address 12.12.61.2 255.255.255.0
[SPU-Eth-Trunk0.9] arp broadcast enable
[SPU-Eth-Trunk0.9] quit
[SPU] interface Eth-Trunk 0.10
[SPU-Eth-Trunk0.10] control-vid 1000 dot1q-termination
[SPU-Eth-Trunk0.10] dot1q termination vid 1000
[SPU-Eth-Trunk0.10] ip address 100.100.100.1 255.255.255.0
[SPU-Eth-Trunk0.10] arp broadcast enable
[SPU-Eth-Trunk0.10] quit
[SPU] interface XGigabitEthernet0/0/1
[SPU-XGigabitEthernet0/0/1] eth-Trunk 0
[SPU-XGigabitEthernet0/0/1] quit
[SPU] interface XGigabitEthernet0/0/2
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 Load Balancing Configuration
330