Huawei quidway s7700 Configuration Manual page 291

Quidway S7700 Smart Routing Switch
Configuration Guide - SPU
Data Preparation
To complete the configuration, you need the following data:
l
l
l
l
l
l
l
Procedure
Step 1 Configure traffic importing on SwitchA.
1.
2.
Issue 01 (2011-07-15)
Server names, connection quantity limits, connection rate limits, and bandwidth rate limits
Name and related parameters of the probe
Server group name, load balancing algorithm, and forwarding mode
Name and matching rule of the Layer 7 classifier
Name and action of the load balancing action profile
Name of the Layer 3 classifier and ACL and Layer 7 classifier bound to the Layer 3 classifier
Name of the load balancing policy and interface where the load balancing policy is applied
Import traffic to the SPU on SwitchA.
<Switch> system-view
[Switch] interface gigabitethernet 3/0/0
[Switch-GigabitEthernet3/0/0] port link-type trunk
[Switch-GigabitEthernet3/0/0] port trunk allow-pass vlan 12
[Switch-GigabitEthernet3/0/0] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/0] quit
[Switch] interface gigabitethernet 3/0/1
[Switch-GigabitEthernet3/0/1] port link-type trunk
[Switch-GigabitEthernet3/0/1] port trunk allow-pass vlan 13
[Switch-GigabitEthernet3/0/1] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/1] quit
[Switch] interface eth-trunk 0
[Switch-Eth-Trunk0] port link-type trunk
[Switch-Eth-Trunk0] port trunk allow-pass vlan 12 to 13
[Switch-Eth-Trunk0] undo port trunk allow-pass vlan 1
[Switch-Eth-Trunk0] quit
[Switch] interface xgigabitethernet5/0/0
[Switch-XGigabitEthernet5/0/0] eth-trunk 0
[Switch-XGigabitEthernet5/0/0] quit
[Switch] interface xgigabitethernet5/0/1
[Switch-XGigabitEthernet5/0/1] eth-trunk 0
[Switch-XGigabitEthernet5/0/1] quit
Add an interface to a VLAN on the SPU.
<Quidway> system-view
[Quidway] sysname SPU
[SPU] interface eth-trunk 0
[SPU-Eth-Trunk0] quit
[SPU] interface xgigabitethernet 0/0/1
[SPU-XGigabitEthernet0/0/1] eth-trunk 0
[SPU-XGigabitEthernet0/0/1] quit
[SPU] interface xgigabitethernet 0/0/2
[SPU-XGigabitEthernet0/0/2] eth-trunk 0
[SPU-XGigabitEthernet0/0/2] quit
[SPU] interface eth-trunk 0.12
[SPU-Eth-Trunk0.12] control-vid 12 dot1q-termination
[SPU-Eth-Trunk0.12] dot1q termination vid 12
[SPU-Eth-Trunk0.12] ip address 10.10.10.1 255.255.255.0
[SPU-Eth-Trunk0.12] arp broadcast enable
[SPU-Eth-Trunk0.12] quit
[SPU] interface eth-trunk 0.13
[SPU-Eth-Trunk0.13] control-vid 13 dot1q-termination
[SPU-Eth-Trunk0.13] dot1q termination vid 13
[SPU-Eth-Trunk0.13] ip address 20.20.20.5 255.255.255.0
[SPU-Eth-Trunk0.13] arp broadcast enable
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 Load Balancing Configuration
280