Huawei quidway s7700 Configuration Manual page 224

Quidway S7700 Smart Routing Switch
Configuration Guide - SPU
Procedure
Step 1 Configure the Switch and the AC to enable APs to communicate with the AC.
# Configure GE2/0/0 and GE2/0/1 of the Switch connected to APs as trunk interfaces, and set
the PVID of the trunk interfaces to 100.
<Quidway> system-view
[Quidway] vlan batch 100 to 102
[Quidway] vlan batch 203 to 205
[Quidway] interface GigabitEthernet 2/0/0
[Quidway-GigabitEthernet2/0/0] port link-type trunk
[Quidway-GigabitEthernet2/0/0] port trunk pvid vlan 100
[Quidway-GigabitEthernet2/0/0] port trunk allow-pass vlan 100 101 102
[Quidway-GigabitEthernet2/0/0] quit
[Quidway] interface GigabitEthernet 2/0/1
[Quidway-GigabitEthernet2/0/1] port link-type trunk
[Quidway-GigabitEthernet2/0/1] port trunk pvid vlan 100
[Quidway-GigabitEthernet2/0/1] port trunk allow-pass vlan 100 203 to 205
[Quidway-GigabitEthernet2/0/1] quit
# Configure XGE1/0/0 of the Switch connected to the AC to transparently transmit packets of
all service VLANs and the management VLAN.
[Quidway] interface XGigabitEthernet 1/0/0
[Quidway-XGigabitEthernet1/0/0] port link-type trunk
[Quidway-XGigabitEthernet1/0/0] port trunk allow-pass vlan 100 to 102 203 to 205
# Configure XGE0/0/1 of the AC connected to the Switch to transparently transmit packets of
all service VLANs and the management VLAN.
<Quidway> system-view
[Quidway] sysname AC
[AC] vlan batch 100 to 102
[AC] vlan batch 203 to 205
[AC] interface XGigabitEthernet 0/0/1
[AC-XGigabitEthernet0/0/1] port link-type trunk
[AC-XGigabitEthernet0/0/1] port trunk allow-pass vlan 100 to 102 203 to 205
[AC-XGigabitEthernet0/0/1] quit
Step 2 Configure basic AC attributes.
# Configure the AC ID, carrier ID, and country code.
[AC] wlan ac-global ac id 1 carrier id other
[AC] wlan ac-global country-code country-code
# Configure a VLANIF interface and assign an IP address to it for Layer 3 packet forwarding.
[AC] interface vlanif100
[AC-Vlanif100] ip address 192.168.0.1 24
[AC-Vlanif100] quit
# Configure a source interface on the AC to communicate with APs.
[AC] wlan
[AC-wlan-view] wlan ac source interface vlanif 100
[AC-wlan-view] quit
Step 3 Configure APs and enable them to go online.
Issue 01 (2011-07-15)
l Create a service set and bind the security profile and traffic profile to the service set.
l Configure a VAP and deliver VAP parameters to implement QoS control for STAs.
NOTE
An AC uses the IP address of the specified source interface as the source IP address. All APs connected
to the AC can learn this IP address.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5 WLAN Configuration
213