Radio Device Programming - Ness D8xD Installer Manual

P101e – P116e
ProgrAm moDe leVel
Installer.
FACtory DeFAUlt
No Radio Devices programmed.
notes
• Radio Device programming is done by
'learning' the code by radio.
• Radio Devices codes can only be
deleted by keypad.
• Some Ness Radio Devices send
separate Alarm and Restore signals.
• For special purposes, radio zones can
be also programmed to accept radio
keys. In this case the zone can not also
be programmed to accept a radio device.
• Late model Ness Radio PIRs and Radio
Reed Switches send Supervision signals.
sUPerVision relAteD oPtions
P65e Supervised Radio Zones.
P66e Radio Supervision Alerts.
P67e Radio Supervision Time.
P75e 12e Radio Supervision Fail Report.
RADIO DeVICeS - OPTION TABle
Zone 1 P101e
Zone 2 P102e
Zone 3 P103e
Zone 4 P104e
Zone 5 P105e
Zone 6 P106e
Zone 7 P107e
Zone 8 P108e
Zone 9 P109e
Zone 10 P110e
Zone 11 P111e
Zone 12 P112e
Zone 13 P113e
Zone 14 P114e
Zone 15 P115e
Zone 16 P116e
TiP:
To prevent
conflicting radio signals
when programming
Radio Devices, disable
each device once you have
finished programming it.
(Remove the battery or open the
RADIO link).
Remember to enable all the
devices when programming is
completed.
106-168 LuX radio Pir
106-170 LuX Pet radio Pir

rADio DeViCe ProgrAmming

each of the zones of the D8x or D16x can be a radio zone. Once programmed, zones
can accept both radio devices and normal zone inputs simultaneously.
The optional 100–200 Ness Radio Interface is required for radio devices to operate.
A radio device is any type of Ness transmitter including Radio PIR, Radio Reed
Switches, Radio Smoke Detector.
PROGRAMMING RADIO DeVICeS
Up to 8 or 16 radio devices can be assigned to the D8x and D16x, (one per zone).
PROGRAMMING SeQUeNCe – NO ReSTORAlS
Suitable for Radio PIRs, Radio Pendant, Radio Smoke Detector.
 Select a zone using P101e – P116e
the arMeD light will be on if a radio Device is already programmed to the zone. Press 0e to delete.
Press 1e

the reaDY light will turn on to indicate that the zone is ready to accept the radio Device.
Send a learn signal from the radio device by inserting the battery.

a. if the radio Device is accepted, the reaDY light will turn off, the arMeD light will turn on and 3 beeps will sound.
B. if the reaDY light stays on and a warning beep sounds, the radio Device is already assigned to another zone and
must be cleared from that zone first.
C. if SuPerviSeD SignaLS have also been successfully recognised, the taMPer light will turn on.
exAMPle: To program a radio Pir on zone 1:
P101e 1e insert the battery in the radio Pir
PROGRAMMING SeQUeNCe – WITH ReSTORAlS
Suitable for Radio Reed Switches.
Alarm the reed switch, ie., move the magnet away from the switch

Leave the reed switch in the alarm condition and wait until radio transmission has stopped.
 Select a zone using P101e – P116e
the arMeD light will be on if a radio Device is already programmed to the zone. Press 0e to delete.
 Press 1e
the reaDY light will turn on to indicate that the zone is ready to accept the radio Device.
Restore the reed switch (place the magnet next to the switch)

a. if the radio Device is accepted, the reaDY light will turn off, the arMeD light will turn on and 3 beeps will sound.
B. the MeMorY light will turn on to indicate that this device sends restorals.
C. if the reaDY light stays on and a warning beep sounds, the radio Device is already assigned to another zone and
must be cleared from that zone first.
D. if SuPerviSeD SignaLS have also been successfully recognised, the taMPer light will turn on.
exAMPle: To program a radio reed Switch with restorals on zone 2:
alarm the reed switch P102e 1e restore the reed switch
DeleTING A RADIO DeVICe:
 Use P101e to P116e to select the zone
Press 0e to clear the device

NeSS D8X / D16X DelUXe CONTROl PANel – INSTAllATION MANUAl
100–527 100–662
universal transmitter Mini radio
reed Switch
(options P109e–P116e apply to D16 only).
(3 beeps will sound)
ness rADio
106–091
Micro radio
reed Switch
73