Keypad - Ness D8xD Installer Manual

keyPAD

The instructions on this page relate to
Ness Saturn and KPX keypads.
Refer to the Ness Navigator user's
manual for operating instructions specific
to the Navigator Touch Screen keypad.
keyPAD beePs
beePs meAning
Any key press.
1 BeeP
Valid Command.
3 BeePS
–– 1 lONG BeeP error.
Mains Power is off
..10.. 10 BeePS
or Panel Battery is low
or A Radio Device
has sent a low battery
signal
or Telephone line Fail
has been detected.
An AutoTime action is
... ... ...
due to begin.
Constant SlOW beeps
An AutoTime action
. . .
will begin in one
Constant FAST beeps
minute.
DISPlAy TeST
To display all available keypad icons
press and hold the button for at least
2 seconds. All icons will be displayed
while the button is held down.
Display Test can be activated at any time
either in operating mode or any program
mode.
NUMBeR OF KeyPADS
Up to 3 lCD keypads can be connected
to a panel.
CABle leNGTH
The maximum allowable cable length is
100m (total cable length to all keypads).
10
keyPAD DisPlAy inDiCAtors in oPerAting moDe
keyPAD iCon
DisPlAy
Zones
1-8 (or 1-16)
OK
READY TO ARM
ARMED
ARMED
HOME
MEMORY
TAMPER
EXCLUDE
LOW
BATTERY
MAINS
OFF
PROG
LINE
keyPAD DisPlAy inDiCAtors in memory moDe
keyPAD iCon
Zone numbers 1–8 or 1–16
(no icons displayed)
ARMeD
ARM2
MAINS
BATTeRy
TAMPeR + 1
TAMPeR + 2
eXClUDe + 1
eXClUDe + 2
eXClUDe + 3
lINe
RADIO, eXClUDe
RADIO, BATTeRy, ZONe
RADIO, BATTeRy, ARM
RADIO, TAMPeR, ZONe
RADIO, HOMe, ZONe
HOMe, ZONe
NeSS D8X / D16X DelUXe CONTROl PANel – INSTAllATION MANUAl
oFF
Zone is sealed. Zone is unsealed.
Zone/s are unsealed. Ready to Arm
or Power fault.
or Panel is armed.
or phone line fault.
Panel is disarmed, Panel is armed,
or Area 1 is disarmed, if or Area 1 is armed, if
using Areas. using Areas.
Area 2 is disarmed. Area 2 is armed if
using Areas.
Home Mode is disarmed. Panel is armed in
Home Mode.
Normal. Memory mode
selected.
Normal. Receiving a radio
signal. (If radio fitted.)
Normal.
Normal.
Normal.
Normal.
Normal. User Program Mode.
Normal Dialler is on line.
memory eVent
Zone alarm
Panel Disarmed
Panel Armed (or Area 1 Armed)
Area 2 Armed
Mains power failure
low Battery
Internal Tamper alarm
external Tamper alarm
Panic alarm
Medical alarm
Fire alarm
Telephone line fail
Radio Key Panic alarm
Radio Device battery low, (Device number is indicated by zone lights)
Radio Key battery low, (Radio Key number is NOT indicated)
Radio Device tamper alarm (Device number is indicated by zone lights)
Radio Supervision alarm (Device number is indicated by zone lights)
Wired Zone Supervision alarm (Zone number is indicated by zone lights)
on FlAsHing
Zone is in alarm.
Day Mode enabled, (see
page 20).
New alarm/s in memory.
A Radio Key or other
radio device has low
battery.
Internal Tamper: Double
Flash with long pause.
external Tamper: Steady
flash.
Zone/s are excluded.
The backup battery
is low.
Mains power is off.
Installer Program Mode.
Phone line fault or
failure to communicate.