P r o g r A m m i n g
Use one of these Quick Start programming summaries for fast setup of your control panel with typical local, Audible Monitored or
Central Station Monitored options.
QUiCk stArt 1 - loCAl system, simPly ProgrAm A User CoDe
STeP
KeySTROKeS
DeSCRIPTION
1
P 1 2 3 e
enters User Program Mode.
2
P 2 0 1 e
Selects the option for User Code 1.
3
_ _ _ _ e
enter your new PIN code followed by e.
4
_ _ _ _ e
enter your new PIN code again.
5
P e
To exit program mode.
QUiCk stArt 2 - AUDible monitoring
STeP
KeySTROKeS
DeSCRIPTION
1
P 1 2 3 e
enters User Program Mode.
2
P 0 0 0 0 0 0 e
enters Installer Program Mode.
3
P 2 0 1 e
Selects the option for User Code 1.
4
_ _ _ _ e
enter your new PIN code followed by e.
5
_ _ _ _ e
enter your new PIN code again.
6
P 8 6 e 4 e
Turns on option P86e 4e
7
P 7 0 e
Selects the option for Telephone Number 1.
8
_ _ _ _ _ _ _ _ e
enter the telephone number followed by e.
9
P e
To exit program mode.
QUiCk stArt 3 - CentrAl stAtion monitoring
STeP
KeySTROKeS
DeSCRIPTION
1
P 1 2 3 e
enters User Program Mode.
2
P 0 0 0 0 0 0 e
enters Installer Program Mode.
3
P 2 0 1 e
Selects the option for User Code 1.
4
_ _ _ _ e
enter your new PIN code followed by e.
5
_ _ _ _ e
enter your new PIN code again.
6
P 8 6 e 2 e
Turns on option P86e 2e
7
P 7 0 e
Selects the option for Telephone Number 1.
8
_ _ _ _ _ _ _ _ e
enter the telephone number followed by e.
8
P 7 2 e
Selects the option for Account Number 1.
10
_ _ _ _ e
enter the Account number followed by e.
11
P e
To exit program mode.
sPeCiAl FUnCtions in ProgrAm moDe
SPeCIAl FUNCTION
SeND DIAlleR TeST RePORT
Send a Dialler Test Report to the telephone number programmed at P70e.
SIReN TeST
Turn the Siren, Reset and Strobe Outputs On. Pressing P e will stop the Siren Test (and also exits
Program Mode).
PANel ReSeT
This function resets the microprocessor. The effect is the same as powering down and powering up
again. INSTAlleR'S TIP: Use P88888888e prior to powering down for a short time. This will save the
current Time Before Next Test Call and the Real Time Clock into permanent memory. On power up
these times will be restored.
DISPlAy SOFTWARe VeRSION
This function displays the panel software version when in program mode. Displayed in decimal
format by the zone leDs. example, version V6.1 is displayed by flashing 6 followed by 1.
12
NeSS D8X / D16X DelUXe CONTROl PANel – INSTAllATION MANUAl
COMMeNT
Program light will turn on. (Default User Code is 123).
The existing code will be displayed.
Keypad codes can be 3 to 6 digits in length.
The new code will be displayed.
Program light will turn off.
COMMeNT
Program light will turn on. (Default User Code is 123).
Program light will flash. (Default Installer Code is 000000).
The existing code will be displayed.
Keypad codes can be 3 to 6 digits in length.
The new code will be displayed.
enables Audible Monitoring.
30 digits maximum.
Program light will turn off.
COMMeNT
Program light will turn on. (Default User Code is 123).
Program light will flash. (Default Installer Code is 000000).
The existing code will be displayed.
Keypad codes can be 3 to 6 digits in length.
The new code will be displayed.
enables Contact ID format.
30 digits maximum.
4 digits maximum. The account number is supplied by your
central monitoring station.
Program light will turn off.
PROGRAM
MODe
USeR
USeR or
INSTAlleR
USeR or
INSTAlleR
USeR or
INSTAlleR
KeyPReSS
P 66666666 e (eight 6's)
P 77777777 e (eight 7's)
P 88888888 e (eight 8's)
P 99999999 e (eight 9's)