Connection Diagram - Ness D8xD Installer Manual

Optional Accessories for D8 & D16
The Weigand Interface and Ness PD
#
ReCeIVeR
both connect to the ReADeR
header
header. Weigand Interface may be
temporarily disconnected to use the
Ness PD.
106-012 Weigand
100-200
interface.
ness radio interface.
Provides connection
for up to 3 addressable
Weigand Readers (Ness
101-014).
See page 82.
Generic Detector Wiring examples
Any ness or generiC
D8x/D16x PAnel HArDWireD DeteCtor
0V
+12V
Zone Zone
C C
TAMP
C
4 wire example
D8x/D16x PAnel
0V
+12V
Zone Zone
C C
TAMP
C
6 wire example
with 24hr Tamper
Siren Wiring examples
ness D8/D16
Control PAnel
TAMP
C
ReSeT
STR
SIReN
ReADeR
header
ReADeR
#
header
Blu
Brn
Grn
Wht
Red
Blk
106-017 ness PD
Portable Download
tool. For easy on-site
copying and re-loading
of programming
options. Requires D8x/
D16x version 7.4 or later.
0v
+12v
n.C.
aLarM
n.C.
n.C.
taMPer
n.C.
DeteCtor
0v
+12v
2K2 n.C.
aLarM
n.C.
2K2
n.C.
taMPer
n.C.
n.o. taMPer SWitCH
(761-002) Colour: BLaCK
2K2
The terminal block should
be mounted inside the
siren cover.
NeSS D8X / D16X DelUXe CONTROl PANel – INSTAllATION MANUAl
CONNeCTION DIAGRAMS
SeRIAl header
(4 pin)
#
To PC serial port
or serial-USB
converter
450-246
serial Cable.
Used for two-way
serial comms or
direct connect to
a PC.
Note. Previous
D8/D16 requires
the 3 pin header
cable 450-185
lUX HW Detector Wiring
D8x/D16x PAnel
0V
+12V
Zone Zone
C C
external trigger to turn on the lUX
nightlight.
Pull to 0v to turn on.
AUX1
AUX2
AUX3
AUX4
+12V
0V
eXAMPle
Using Aux1 on your D8x/D16x to turn
on the the lUX HW nightlight from the
keypad or even remotely.
INSTAlleR PROGRAMMING
P141e 4e should be ON.
OPeRATION
• LCD keypad, press 11* or 11# to turn
on/off
•Navigator keypad, use the Aux Control
menu.
externAl
Horn
SPeaKer
(noi110)
StroBe LigHt
(noi300)
AUX header
106-013 relay board. 106-011 output expander.
Provides 4 relay Provides 16 programmable
outputs suitable for open collector outputs.
switching low voltage See page 54.
accessories.
The Relay Board and the Output expander Board connect to
the Aux header but not at the same time.
ness lUx HW
DeteCtor
Additional +12V terminal.
Fast reacting output is low (0v)
when movement is detected.
Nightlight status output. Pulls low
(0v) when light is on.
* HINT. Use a 450-159 loom (cut and use one end
only into the panel's Aux header).
Or a 106-011 output expander or 106-013 relay
board can be used and wired accordingly.
internAl
AUX header
9