Toshiba e-studio200l Service Handbook page 41

Error code Classification
E910 Finisher jam
(Bridge unit)
E920
E930
E940
E950 Job separator jam
E951
E960 Offset tray jam
E961
E9F0 Finisher jam
(Puncher unit)
EA10 Finisher jam
(Finisher unit)
EA20
EA30
EA40
EA50
EA60
EA70
EAB0 Finisher jam
(Saddle Stitcher sec-
tion)
EAC0
EAD0 Other paper jam
© 2004 - 2010 TOSHIBA TEC CORPORATION All rights reserved
Contents
Jam at the bridge unit transport sensor-1: The
paper does not reach the bridge unit transport sen-
sor-1 after it has passed the exit sensor.
Stop jam at the bridge unit transport sensor-1: The
trailing edge of the paper does not pass the bridge
unit transport sensor-1 after its leading edge has
reached the sensor.
Jam at the bridge unit transport sensor-2: The trail-
ing edge of the paper does not reach the bridge unit
transport sensor-2 after its leading edge has
reached the bridge unit transport sensor-1.
Stop jam at the bridge unit transport sensor-2: The
trailing edge of the paper does not reach the bridge
unit transport sensor-2 after its leading edge has
reached the bridge unit transport sensor-2.
Jam not reaching the job separator transport sen-
sor: The paper has passed through the exit sensor
does not reach the job separator transport sensor.
Stop jam at the job separator transport sensor: The
trailing edge of the paper does not pass the job sep-
arator transport sensor.
Jam not reaching the offset tray transport sensor:
The paper has passed through the exit sensor does
not reach the offset tray transport sensor.
Stop jam at the offset tray transport sensor: The
trailing edge of the paper does not pass the offset
tray transport sensor.
Punching jam: Punching is not performed properly.
[MJ-1025 (When MJ-6005 is installed)]
Paper transport delay jam: The paper which has
passed the bridge unit does not reach the inlet sen-
sor. [MJ-1022/1025]
Paper transport stop jam: The paper does not pass
through the inlet sensor. [MJ-1022/1025]
Power-ON jam: Paper exists at the inlet sensor
when power is turned ON. [MJ-1022/1025]
Door open jam: The finisher has been released
from the equipment during printing. [MJ-1022/1025]
Stapling jam: Stapling is not performed properly.
[MJ-1022/1025]
Early arrival jam: The inlet sensor detects the paper
earlier than a specified timing. [MJ-1022]
Stack delivery jam: It cannot deliver the stack of
paper on the intermediary process tray to the stack
tray. [MJ-1022/1025]
Saddle paper transport stop jam: The paper which
passed through the inlet sensor does not reach or
pass through the folding position sensor. [MJ-1025]
Saddle transport delay jam: The paper which has
reached the inlet sensor does not pass through this
sensor. [MJ-1025]
Print end command time-out jam: The printing has
not finished normally because of the communica-
tion error between the SYS board and LGC board
at the end of printing.
e-STUDIO200L/202L/203L/230/230L/232/233/280/282/283
2 - 5
Troubleshooting
P. 5-35
P. 5-35
P. 5-35
P. 5-35
P. 5-11
P. 5-11
P. 5-11
P. 5-11
P. 5-36
P. 5-37
P. 5-38
P. 5-39
P. 5-40
P. 5-41
P. 5-42
P. 5-43
P. 5-45
P. 5-45
P. 5-46
ERROR CODE AND SELF-DIAGNOSTIC MODE
2