Daikin FTX-N/U Manual page 348

FTX-N/U, FVXS-N, FDMQ-R Series
01_EN_3P510048-1A.fm Page 5 Wednesday, December 27, 2017 2:27 AM
FAN SPEED CONTROL BUTTON
8
Press this button to select the fan speed, HIGH,
MEDIUM or LOW, of your choice.
TEMPERATURE SETTING BUTTON
Use this button for SETTING TEMPERATURE.
9
(Operates with the front cover of the remote controller
closed.)
PROGRAMMING TIMER BUTTON
Use this button for programming "START and/or STOP"
10
time. (Operates with the front cover of the remote con-
troller opened.)
TIMER MODE START/STOP BUTTON
11
Refer to page 7.
TIMER RESERVE/CANCEL BUTTON
12
Refer to page 7.
OPERATION MODE SELECTOR BUTTON
13
Press this button to select OPERATION MODE.
FILTER SIGN RESET BUTTON
14
Refer to the section of MAINTENANCE in the operation
manual attached to the indoor unit.
INSPECTION/TEST OPERATION BUTTON
15
This button is pressed for inspection or test operation.
Do not use for normal operation.
EMERGENCY OPERATION SWITCH
16
This switch is readily used if the remote controller does
not work.
RECEIVER
17
This receives the signals from the remote controller.
OPERATING INDICATOR LAMP (Red)
18
This lamp stays lit while the air conditioner runs.
It flashes when the unit is in trouble.
TIMER INDICATOR LAMP (Green)
19
This lamp stays lit while the timer is set.
AIR FILTER CLEANING TIME INDICATOR LAMP (Red)
20
Lights up when it is time to clean the air filter.
DEFROST LAMP (Orange)
21
Lights up when the defrosting operation has started.
(For cooling only type this lamp does not turn on.)
FAN/AIR CONDITIONING SELECTOR SWITCH
22
Set the switch to "
for HEAT or COOL.
COOL/HEAT CHANGEOVER SWITCH
23
Set the switch to "
(HEAT) for HEAT.
" (FAN) for FAN and " " (A/C)
" (COOL) for COOL and " "
346
NOTE
• For the sake of explanation, all indications are shown on the
display in Fig. 1-1 contrary to actual running situations.
• Fig. 1-2 shows the remote controller with the front cover
opened.
• Fig. 2 shows this remote controller can be used in conjunc-
tion with the one provided with the VRV system.
• If the air filter cleaning time indicator lamp lights up, clean
the air filter as explained in the operation manual provided
with the indoor unit.
After cleaning and reinstalling the air filter, press the filter
sign reset button on the remote controller. The air filter
cleaning time indicator lamp on the receiver will go out.
• The DEFROST lamp will flash when the power is turned on.
This is not a malfunction.
3. HANDLING FOR WIRELESS REMOTE
CONTROLLER
• Precautions in handling remote controller
• Direct the transmitting part of the remote controller to
the receiving part of the air conditioner.
If something blocks the transmitting and receiving path of the
indoor unit and the remote controller as curtains, it will not
operate.
• Transmitting distance is approximately 23 ft..
• Do not drop or get it wet.
It may be damaged.
• Never press the button of the remote controller with a
hard, pointed object.
The remote controller may be damaged.
• Installation site
It is possible that signals will not be received in rooms that
have electronic fluorescent lighting. Please consult with the
salesman before buying new fluorescent lights.
If the remote controller operated some other electrical appa-
ratus, move that machine away or consult your dealer.
Placing the remote controller in the remote controller
holder
Install the remote controller holder to a wall or a pillar with the
attached screw. (Make sure it transmits.)
EDUS091558E
Receiver
2 short beeps from the
receiver indicates that
the transmission is
properly done.
5
3P510048-1A