Table Of Contents - Panasonic S-LINK V User Manual

Before Using This System ························· 5
Introduction ·············································· 6
Warnings ··············································· 6
Instructions for Safe Use ··························· 7
Ambient conditions ······························ 7
Instructions for Designing ·························· 8
Instructions for Use ···································· 8
Fail-safe function ································· 8
Conformity to EC Directives ··················· 8
Use with S-LINK system ······················· 8
Instructions for Installation ························· 9
Instructions for Disposal ···························· 9
Hook-up cable connectors ····················· 9
Wiring ··············································· 9
Others ··············································· 9
Designing / Installation Procedures ············· 10
Chapter 1 Designing System ···················· 13
System Configuration ······························· 14
Outline of Design ···································· 16
Selection of Controller or Control board ·······16
I/O Control Points ···································16
Transmission Distance ·····························16
Outputting Error Signals ···························17
Connection of End Unit ····························18
Selection of Control Cable and Connector
Link Cable ·············································18
Control cable selection method: (For use of
SL-VCU1 only) ···································18
Connector link cable selection method:
(For use of SL-VCU1 only) ···················18
Making of Branch Lines Using Cable
Connectors ············································19
Calculation of Total Current Consumption Value ·20
Power Supply Capacity of System ·············· 20
Example: Calculation of current
consumption ······································22
Calculation of Voltage Drop Value ··············23
Rated voltage (V) ·······························23
Necessity of Local Power Supply Unit ·········24
Designing of system using local power
supply method ···································24
Connection of DC 2-Wire Output Device to
Input Unit ··············································· 26
Example: Connection of DC 2-wire sensor 27
Transmission Delay Time ·························· 28
Response delay time ···························28
Operation at power-on ·························30
Error signal outputting delay time ···········30
System setting time ·····························31
Selection of Output Holding Function for
Output Unit ············································ 32
Output holding function setting method ···32
Address Setting ······································ 33
Setting of PLC I/O connector numbers ····33
Setting of I/O unit addresses ·················33
Example: Address setting ·····················34
Contents
Chapter 2 Wiring ····································· 35
Flowchart ·············································· 36
Basic Procedures ···································· 37
Connector hook-up work ······················37
Cutting of exclusive 4-core flat cable·······37
How to use exclusive hook-up pliers
(SL-JPS, SL-JPC, SL-JPE) ··················38
Hook-up of Connector ······························39
Hook-up method of SL-JK connector
for cable end and SL-JK1 connector
for 'T'- branch ···································39
Hook-up method of SL-J1A connector
for 'T' - branch and SL-J3A connector
for cable extension ······························41
Hook-up method of SL-CP1, SL-CP2,
and SL-CP3 snap male connectors and
SL-CJ1 and SL-CJ2 snap female connectors · 44
Connection to Terminal Block ····················46
Extension of Main / Branch Line Cable ········47
Extension of exclusive 4-core flat cables ·47
Extension of cable excluding
exclusive 4-core flat cables ···················47
Extension of cable to I/O device·············47
Installation ·············································48
Installation of each unit ························48
Power Supply ········································50
Construction ··········································· 50
Power supply to system ·······················50
Connection of Each Unit ···························51
Connection of controller ·······················51
Connection of bus direct-connection
type controller and control board ············52
Connection of PLC I/O Connector ··········53
Connection of I/O unit ··························55
Connection of I/O device ······················56
Connection of main line cable to end unit ·57
Connection of local power supply unit ····58
Local power supply to system ···············58
Installation method of batteries ··············59
Chapter 3 Starting System ······················· 61
Flowchart ·············································· 62
Check before Starting ······························64
Wiring Check ·········································· 64
Check of wiring conditions of controller
and control board ·······························64
Check of PLC I/O connectors ················65
Check of cable for short-circuit ··············65
Power-on (Main Power and Local Power) ····66
Starting ················································· 66
CONFIG mode ···································66
Check of Recognized Addresses ················70
CHECK mode ····································70
3