Panasonic S-LINK V User Manual page 89

● Specifications
Type
Model No.
Supply voltage (Note 1)
Current consumption
Connecting method
Number of I/O control Maximum 512 points (Note 4) (using DIP switches, in increments / decrements of 32 points / I/O setting using the
points program in increments / decrements of 16 points is also possible).
Transmission
BUSY
Red LED (Lights up when an error occurs, blinks when the cause of the error is eliminated, turns off when normal
Error
operation is performed.)
Compatible bus
Ambient tempera-
ture (Note 6)
Ambient humidity
(Note 6)
Noise immunity
(Note 6)
Voltage withstandability
(Note 6)
Insulation resistance
(Note 6)
Vibration resistance
(Note 6)
Shock resistance
(Note 6)
Grounding method
Interruption will be performed if an error or input
Interruption function
change occurs
(Note 7)
(enabling / disabling this function is possible).
Notes: 1) 24V DC and 5V DC are insulated from each other. For the SL-VVMES2, the S-LINK V transmission ports are also insulated.
2) The current consumption value is the total of the maximum current value (D-G line only) supplied to the S-LINK V I/O units and the
current consumption value of the S-LINK V control board.
3) This product is not equipped with any short-circuit protective function.
For this reason, select a power supply unit having short-circuit protective function (fuse, etc.).
4) For the SL-VVMES2, the maximum number of I/O control points is 1,024 points (512 points, maximum ´ 2 ports).
5) If you need a driver, download the driver from "our Internet homepage: https://panasonic.net/id/pidsx/global ."
[We can provide drivers for DOS, Windows 95/98/Me(32bit), Windows NT 4.0(32bit), Windows2000/XP/7(32bit) and Windows
10(64bit).] If you cannot access to our Internet homepage, please contact the store where you bought our product or our sales office.
6) This value is for the control board single body. If the control board is installed on the computer, compare the specifications of the con-
trol board with those of the computer, and observe the specifications showing the lower value.
7) The interruption function can be enabled or disabled for each point. However, the interruption condition (ON→OFF / OFF→ON) is ap-
plied to all the input points, and application to each point is not possible.
For PCI bus
SL-VPCI
[24V DC] 85mA or less (Note 2)
[24V DC (power supply to load driving S-LINK V I/O unit)]
Maximum current supplied: 7A (For one port for SL-VVMES2) (Note 3)
[5V DC] 315mA or less
'T'-branch connection or multi-drop connection
Orange LED (Lights up at starting and during system setting operation, turns off during transmission)
PCI bus (Note 5)
0 to +55ºC (No dew condensation), Storage: -20 to +70ºC
Power line: 500Vp, 10ms cycle, 1μs pulse width
Common: 1,000Vp, 10ms cycle, 1μs pulse width (with noise simulator)
1,000V AC for one min. between external terminal and ground
20MΩ, or more, with 500V DC megger between external terminal and ground
10 to 150Hz frequency, 0.75mm amplitude or maximum acceleration 49m/s² in X, Y and Z directions for two
hours each
2
98m/s acceleration (approx. 10G) in X, Y and Z directions for three times each
Bracket: Floating, S-LINK V system side: C-connection
[S-LINK V system side] 24V DC
[Bus side] 5V DC±5%
Green LED (blinks during transmission)
20 to 85% RH, Storage: 20 to 85% RH
Setting of 'Not used,' IRQ1 to IRQ7, and status / ID is
possible.
[Status / ID transfer capability: D08 (O)]
Interruption will be performed if an error or input
change occurs (enabling / disabling this function is
possible).
Specifications
For VME bus
SL-VVMES2
%
+10
− 5
[24V DC] 88mA or less (Note 2)
[5V DC] 880mA or less
VME bus
89