Panasonic S-LINK V User Manual page 104

Specifications
● Specifications
Type
Mode No.
Supply voltage
Unit side
Current
consump-
tion
Output side
(When all points are ON)
(Note 1)
Allowable passing cur-
rent (Note 2)
Address setting
Output
Output operation
Short-circuit protection
Number of output points
Power Green LED (lights up when there is power between the "24V DC" power supply terminal and "0V", and between "+" and "-")
Transmission
Output
Output holding function
Ambient temperature
Ambient humidity
Noise immunity
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Mounting
Tightening torque
Material
Weight
Notes: 1) The current consumption value shown in the 'Unit side' area indicates the current consumption in the main circuit.
The current consumption value shown in the 'output side' area indicates the current consumption in the output circuit.
2) Each value includes the current consumption of this terminal and connected machine.
3) If one of the output channels is shorted, the short-circuit protective function will be activated to protect all the channels, and outputting
signals to the external machine will be stopped. Eliminate the cause of the problem, and the system will be automatically restored.
4) If this product is stored in the control panel together with the other units, the temperature may rise above the specified operation tem-
perature due to the heat generated by the other units.
In this case, install a cooling fan, etc. so that the ambient temperature can be in the specified range.
104
4-channel
SL-VTBP4
24V DC±10% (Supplied from S-LINK V controller or separate power supply)
25mA or less 30mA or less
40mA or less 60mA or less
(When all points are ON)
Total: 1A or less Total: 2A or less
NPN open-collector transistor (photo-isolation)
• Masimum sink current: 200mA
• Applied voltage: 30V DC or less (between output and 0V)
• Residual voltage: 1.5V or less (at 200mA sink current)
The output transistor will be turned on if the output signal is sent from the signal transmission line.
4 points
Green LED (blinks when the synchronization signal is sent from the S-LINK V controller)
Orange LED (lights up when the output signal of the corresponding channel is turned ON)
-10 to +55°C (No dew condensation or icing allowed) (Note 4), Storage: -20 to +70°C
Power line: 500Vp, 10ms cycle, 1μs pulse width
Common: 1,000Vp, 10ms cycle, 1μs pulse width (with noise simulator)
1,000V AC for one min. between all terminals connected together and enclosure
20MΩ, or more, with 500V DC megger between all terminals connected together and enclosure
10 to 150Hz frequency, 0.75mm amplitude or maximum acceleration 49m/s² in X, Y and Z directions for two
hours each
2
490m/s acceleration (approx. 50G) in X, Y and Z directions for three times each
Mounted on DIN rail or by tightening screws
Terminal screw: 0.5N･m or less, Mounting screw: 1.2N･m or less
Approx. 90g Approx. 130g
8-channel 16-channel
SL-VTBP8 SL-VTBP16
40mA or less
100mA or less
(When all points are ON)
Total: 4A or less
Using switches, in the range of 0 to 511
0.4V or less (at 16mA sink current)
Incorporated (Note 3)
8 points 16 points
Incorporated
35 to 85% RH, Storage: 35 to 85% RH
Enclosure: ABS, Terminal area: PBT
Approx. 220g
32-channel
SL-VTBP32
45mA or less
180mA or less
(When all points are ON)
Total: 7A or less
32 points
Approx. 225g