Panasonic S-LINK V User Manual page 133

● Specifications
Type
Model No.
Supply voltage
Current consumption
Address setting
Relay contact 1a (Note 1)
• Switching capacity: 50V, 3A AC (resister load)
However, if compatibility with the CE is not necessary, use of 250V, 3A AC is possible.
Output
30V, 3A DC (resister load)
• Electrical service life: 100,000 times of operation or more (rated load, switching frequency of 20 times/min)
• Mechanical service life: 20,000,000 times of operation or more (switching frequency of 180 times/min)
Output operation
Number of output points
Power
Transmission
Operation
Output holding function
Ambient temperature (Note 2)
Ambient humidity
Noise immunity
Voltage withstandability
Insulation resistance
Vibration resistance 10 to 150Hz frequency, 0.75mm amplitude or maximum acceleration 49m/s² in X, Y and Z directions for two hours each
Shock resistance
Mounting
Tightening torque
Material
Cable
Weight
Accessories
Notes: 1) This product is incorporated with the PA-N relay manufactured by Panasonic Corporation. However, when you replace the relay, you
can also use the PhotoMOS relay manufactured by Panasonic Corporation.
For a detailed description, refer to the Instruction Manual enclosed with the SL-VTPR□.
2) If this product is stored in the control panel together with the other units, the temperature may rise above the specified operation tem-
perature due to the heat generated by the other units.
In this case, install a cooling fan, etc. so that the ambient temperature can be in the specified range.
*Ambient temperature and number of photoMOS relay ON points - Load current characteristics
The upper limit value of the load current depends on the ambient temperature and the number of photoMOS relay ON points.
SL-VTPR8+AQZ202D
4.00
No. of outut-ON relay pts.: 1 or 2
3.00
2.00
1.00
No. of outut-ON relay pts.: 7 or 8
0
0
-20
Ambient temperature (°C)
SL-VTPR8+AQZ205D
2.00
No. of outut-ON relay pts.: 1 or 2
1.50
1.00
0.50
No. of outut-ON relay pts.: 7 or 8
0
0
-20
Ambient temperature (°C)
4-channel
SL-VTPR4
24V DC±10% (Supplied from S-LINK V controller or separate power supply)
90mA or less (When all points are ON)
Using switches, in the range of 0 to 511
The output relay is turned ON if the output signal from the signal transmission line is turned ON.
4 points
Green LED (lights up when the power is supplied)
Green LED (blinks when the synchronization signal is sent from the S-LINK V controller)
Orange LED (lights up when each channel relay is turned ON)
-10 to +55°C (No dew condensation or icing allowed), Storage: -20 to +70°C
35 to 85% RH, Storage: 35 to 85% RH
Power line: 500Vp, 10ms cycle, 1µs pulse width
Common: 1,000Vp, 10ms cycle, 1µs pulse width (with noise simulator)
1,000V AC for one min. between all terminals connected together and enclosure
20MΩ, or more, with 500V DC megger between all terminals connected together and enclosure
2
490m/s acceleration (approx. 50G) in X, Y and Z directions for two hours each
Mounted on DIN rail or by tightening screws
Enclosure: PC-ABS resin, Cover: Polycarbonate, DIN rail stopper: POM, Relay remover key: POM
0.5mm
Approx. 100g
Cover: 1 pc., Switch cap: 1 pc., Relay remover key: 1 pc.
No. of outut-ON relay pts.: 3 or 4
No. of outut-ON relay pts.: 5 or 6
20 40 60
No. of outut-ON relay pts.: 3 or 4
No. of outut-ON relay pts.: 5 or 6
20 40 60
150mA or less (When all points are ON)
Incorporated
Mounting screw: 0.8N·m or less
2
4-core flat cable, 0.6m long
SL-VTPR8+AQZ204D
0.40
No. of outut-ON relay pts.: 1 or 2
No. of outut-ON relay pts.: 3 or 4
0.30
0.20
No. of outut-ON relay pts.: 7 or 8
0.10
0
0 20
-20
Ambient temperature (°C)
SL-VTPR8+AQZ207D
0.80
No. of outut-ON relay pts.: 1 or 2
No. of outut-ON relay pts.: 3 or 4
0.60
No. of outut-ON relay pts.: 5 or 6
0.40
0.20
No. of outut-ON relay pts.: 7 or 8
0
0 20
-20
Ambient temperature (°C)
Specifications
8-channel
SL-VTPR8
8 points
Approx. 160g
No. of outut-ON relay pts.: 5 or 6
40 60
40 60
133