0-4: Mix - Korg MICROX X50 Parameter Manual

• Press the center of the ClickPoint to highlight the field in
the display, use [π][†] to make your choice, and press
the center to confirm.
• Use PROG BANK [A]–[GM] to select a bank (☞p.1)
• Use "Select by Category" to choose from the desired
category (☞p.36)
• Receiving a MIDI program change message can also be
used to select a program (☞p.171)
microX:
• Turn the [VALUE] dial.
• Press the center of the ClickPoint to highlight the field in
the display, use [π][†] to make your choice, and press
the center to confirm.
• Use "Select by Category" to choose from the desired
category (☞p.36)
• Receiving a MIDI program change message can also be
used to select a program (☞p.171)
If the "Status" (2–1a/2a) is either INT or BTH, pro-
grams can be selected by receiving MIDI program
change messages. When the multi set is changed, X50/
microX will transmit a song select message. Also, when
a song select message is received from the specified
source, the multi set will change. If the "Status" is EX2,
a "–" will be displayed before the program number.
Tracks whose "Status" is EX2 will transmit the bank
number that was selected in the "Bank(EX2) LSB,"
"Bank(EX2) MSB" (2–1a).
PLAY/MUTE
This specifies the play/muted status of each track.
PLAY: The track will play.
MUTE: The track will be muted (silent).
0–2(3)c: Selected Track Information
Selected Track Information
This shows the currently selected track, program bank,
number, name, and MIDI channel.
■ 0–2(3): UTILITY
☞"Write Multi," "Copy From Combi," "GM Initialize"(0–1)
For details on how to select the desired utility function, refer
to "PROG 0–1: UTILITY."
Select by Category
You can select the program for each track by category. This
command can be selected when a Program page (Prog..8,
Prog..16) is displayed.
☞PROG 0–1
58
0–4: Mix..8
0–5: Mix..16
Here you can set the pan and volume of each track.
0–4a
0–4(5)a: Pan, Volume
Pan
Sets the pan of tracks 1–16.
L001...C064...R127: A setting of L001 is far left, and R127 is
far right. A setting of C064 will reproduce the pan setting of
the oscillator in Program mode.
OSC1
Left
[PLAY, MUTE]
Left
OSC1
If a mono-type insertion effect is inserted, this setting will be
ignored. In this case, the 8: InsertFX, Setup page "Pan
(CC#8)" setting will adjust the pan of the sound following
the insertion effect.
RND: The sound will be panned randomly at each note-on.
Volume
Sets the volume of tracks 1–16.
(Mixer T01...08)
(Mixer T09...16)
[RND, L001...C064...R127]
OSC2
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Center Right
Pan (CC#10)
C064
L032
L001
R096
R127
Center Right
OSC2
OSC1: Amp1 Pan=C064
OSC2: Amp2 Pan=C064
Left Center Right
Pan (CC#10)
C064
L032
L001
R096
R127
Left Center
Right
If "Status" (2–1a/2a) is INT or BTH, CC#10 Panpot can
be received to control the panning. When receiving
CC#10, a value of 0 or 1 is far left, 64 is center, and 127 is
far right. If "Multi Mode" (GLOBAL 0–2a) is set to for
Master, the pan setting you specify here will be trans-
mitted via MIDI for tracks whose "Status" is EXT, EX2,
or BTH when you switch the multi set number. (RND
removes)
When "Status" (2–1a/2a) is INT or BTH, CC#7 Volume
can be received to control the volume. The volume of a
track is determined by multiplying the MIDI Volume
(CC#7) and Expression (CC#11) values. If "Multi
Mode" (GLOBAL 0–2a) is set to for Master, the volume
setting you specify here will be transmitted via MIDI
for tracks whose "Status" is EXT, EX2, or BTH when
you switch the multi set number.
OSC1: Amp1 Pan=L032
OSC2: Amp2 Pan=R096
Left Center Right
Pan (CC#10)
C064
L032
L001
R096
R127
Left Center Right
[000...127]