Prog 8: Ed-Insertfx; 8-1: Bus - Korg MICROX X50 Parameter Manual

PROG 8: Ed–InsertFX
☞For details on insertion effect, refer to p.97 "6. Effect
Guide."
8–1: BUS
These settings specify the bus on which the output of the
oscillator will be sent, and adjust the send levels to the mas-
ter effects.
The following diagram shows the LCD screen when "Mode
(Oscillator Mode)" (1–1a) is set to Single or Double.
8–1a
8–1a: BUS
BUS Select:
BUS Select (All OSCs) [L/R, IFX, 1, 2, 1/2, Off]
Specifies the bus to which oscillators 1 and 2 will be sent.
If this is set to 1/2, the oscillator pan settings (6–1b, 6–4)
will be used to output the sound in stereo from (INDI-
VIDUAL OUTPUT) 1/2. When the oscillator pan is
controlled by CC#10 (pan) or AMS (Alternate Modula-
tion Source), the sound will be output with the pan set-
ting that is in effect at note-on. Unlike the case when
this is set to L/R to output the sound from (MAIN OUT-
PUT) L/MONO and R, the pan of a sounding note will
not change in real-time.
If you wish to adjust the pan in real-time while playing
a note and output the sound from (INDIVIDUAL OUT-
PUT) 1/2, set "BUS Select" to IFX, set "IFX" to 00: No
Effect, and set the "BUS Select" (8–2a) after passing
through IFX to 1/2.
MFX Send:
OSC1 Send1
Sets the volume (send level) at which the output of OSC1
will be sent to master effect 1. This is valid when "BUS
Select" is set to L/R or Off.
If "BUS Select" is set to IFX, the send levels to master effect 1
and 2 are set by "S1 (Send1(MFX1))" and "S2
(Send2(MFX2))" (8–2a) after passing through IFX of the
Setup page.
OSC1 Send2
Sets the volume (send level) at which the output of OSC1
will be sent to master effect 2 (☞"OSC1 Send1").
OSC2 Send1
OSC2 Send2
Sets the volume (send level) at which the output of OSC2
will be sent to master effects 1 and 2. These parameters will
be valid when "Mode (Oscillator Mode)" (1–1a) is set to
Double and "BUS Select" is set to L/R or Off (☞"OSC1
Send1").
28
CC#93 will control the Send 1 level for OSC 1 and 2,
and control change #91 will control the Send 2 level for
OSC 1 and 2. These are controlled on the global MIDI
channel "MIDI Channel" (GLOBAL 1–1a).
The actual send level is determined by summing these
values with the send level setting of each oscillator.
8–1b: Use DKit Setting
The LCD screen shown below is for when "Mode (Oscillator
Mode)" (1–1a) is set to Drums.
8–1b
Use DKit Setting
This will be available when "Mode (Oscillator Mode)" is set
to Drums. If the "Mode (Oscillator Mode)" is Single or
Double, this setting has no effect.
On (checked): The "BUS (BUS Select)" (GLOBAL 4–3a) set-
ting for each key of the selected drum kit will be used.
Check this when you want to apply an insert effect to an
individual drum instrument, or to output an individual
drum instrument to one of the INDIVIDUAL OUTPUT
jacks.
Off (unchecked): The setting of the "BUS Select," "MFX
Send" (8–1a) parameter described below will be used. All
drum instruments will be sent to the specified bus.
■ 8–1: UTILITY
☞"Write Program" (0–1)
For details on how to select the desired utility function, refer
to "PROG 0–1: UTILITY."
Copy Insert Effect
This command copies effect settings from Program, Combi-
nation, Multi set.
1 Select "Copy Insert Effect" to access the dialog box.
[000...127]
2 In "From" select the copy source mode, bank, and num-
ber.
X50:
You can press a PROG BANK button to select a bank.
[000...127]
You can also use numeric buttons [0]–[9] and the [ENTER]
button to select a number.
3 Select the effect that you wish to copy. You can also copy
from a master effect.
[000...127]
If you are copying from a master effect, the result may
[000...127]
not be identical, due to differences in the routing and
level settings of a master effect.
[Off, On]