6-4: Lvl/Pan (Amp2 Level/Pan); 6-5: Mod. (Amp2 Modulation); 6-6: Eg (Amp2 Eg); Prog 7: Ed-Arp/Ctrls (Arpeggiator/Controls) - Korg MICROX X50 Parameter Manual

Music synthesizer and synthesizer/controller
Hide thumbs Also See for MICROX X50:
Table of Contents

Advertisement

■ 6–3: UTILITY
☞"Write Program" (0–1), "Copy Oscillator," "Swap Oscilla-
tor" (1–1)
For details on how to select the desired utility function, refer
to "PROG 0–1: UTILITY."
Sync Both EGs
The amp 1 EG and the amp 2 EG can be edited simulta-
neously. (Editing either one will cause the other to change.)
Choose "Sync Both EGs" from the utility menu, and press
the center of the ClickPoint; a check mark will appear at the
left of "Sync Both EGs." (☞4–5: UTILITY
6–4: Lvl/Pan
(Amp2 Level/Pan)
6–5: Mod.
(Amp2 Modulation)
6–6: EG
(Amp2 EG)
These will appear when "Mode (Oscillator Mode)" (1–1a) is
Double. (☞"PROG 6: Ed–Amp1/2")
PROG 7: Ed–Arp/Ctrls
(Arpeggiator/Controls)
Here you can make settings for the arpeggiator used in the
program.
You can also assign the functions of the following control-
lers.
X50:
The B-mode functions of REALTIME CONTROLS [1]–
[4] knobs, and the functions of [SW1] and [SW2].
microX:
[1]–[4] knobs.
These arpeggiator settings can be linked when you switch
programs. To link, check the Program item in "Auto Arp.
"Program" (GLOBAL 0–1c): On.
)
The arpeggiator can be switched on/off by the [ARP ON/
OFF] button. When on, the LED will light.
The settings of the REALTIME CONTROLS C-mode [ARP-
GATE] knob, [ARP-VELOCITY] knob, [ARP-LENGTH]
knob, [TEMPO] knob, and [ARP ON/OFF] button can be
saved for each program.
These settings will be valid when Auto Arp. "Program"
is On.
You can control the arpeggiator from an external
sequencer, or record arpeggio note data on an external
sequencer. (☞p.178)
"Pattern," "Resolution," "Octave," "Sort," "Latch,"
"Key Sync.," "Keyboard," and " (Tempo)" can also be
set in the Arp. Play page of 0: Play.
7–1: Setup
7–1a
7–1a: Arpeggiator Setup
☞Refer to OG
Pattern*
Selects the arpeggio pattern.
Preset-0: UP
Preset-1: DOWN
Preset-2: ALT1
Preset-3: ALT2
Preset-4: RANDOM
U000...U250
Preset-0–Preset-4 are preset arpeggio patterns, U000–U250
are user arpeggio patterns. User arpeggio patterns can be
created in GLOBAL 5: Arp. Pattern.
X50:
Arpeggio patterns U000–U250 can be selected using
the numeric buttons [0]–[9] and the [ENTER] button.
The B-mode functions of REALTIME CONTROLS
(Arpeg. Setup)
p.91,
p.91.
X50:
microX:
[Preset-0...Preset-4, U000...U250]
Preset Arpeggio Pattern
Preset Arpeggio Pattern
Preset Arpeggio Pattern
Preset Arpeggio Pattern
Preset Arpeggio Pattern
for Preloaded User Arpeggio Pattern
7–1b
25

Advertisement

Table of Contents
loading

This manual is also suitable for:

Micro x

Table of Contents