46: St.mod. Delay; (Stereo Modulation Delay); 47: St.dynamicdly; (Stereo Dynamic Delay) - Korg MICROX X50 Parameter Manual

Music synthesizer and synthesizer/controller
Hide thumbs Also See for MICROX X50:
Table of Contents

Advertisement

46: St.Mod. Delay

(Stereo Modulation Delay)

This stereo delay uses an LFO to sweep the delay time. The
pitch also varies. You will obtain a delay sound with swell
and shimmering. You can also control the delay time using a
modulation source.
Stereo In - Stereo Out
Left
Right
D
-mod
Response
LFO: Tri / Sine
LFO Sync
Mod Mode (Modulation Mode)
Switches between LFO modulation control and modulation source
control
a
Src (Source)
Selects the modulation source that controls delay time
Dmod
Reversed L/R control by modulation source
b
Respons (Response)
Sets the rate of response to the modulation source
LFO Wave (LFO Waveform)
Selects LFO Waveform
c
Shape (LFO Shape)
Determines how much the LFO waveform is changed
LFO Freq (LFO Frequency)
d
Sets the LFO speed
LFO Sync
Switches LFO reset off/on
e
Src (Source)
Selects the modulation source that resets the LFO
L Phase (L LFO Phase)
Sets the phase obtained when the left LFO is reset
f
R Phase (R LFO Phase)
Sets the phase obtained when the right LFO is reset
L Depth
Sets the depth of the left LFO modulation
g
R Depth
Sets the depth of the right LFO modulation
L Dly (L Delay Time)
Sets the left delay time
h
R Dly (R Delay Time)
Sets the right delay time
L Fb (L Feedback)
Sets the feedback amount of left delay
i
R Fb (R Feedback)
Sets the feedback amount of right delay
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
j
(Source)
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
b: Dmod
When the modulation source is used for control, this parameter
reverses the left and right modulation direction.
130
Delay
Feedback
Delay
D-mod
L/R: +/+ +/–
LFO Shape
LFO
Modulation Mode
LFO Phase
L/R:+/+, L/R:+/–
–100...+100
0.02...20.00Hz
–180...+180
–180...+180
–100...+100
–100...+100
–Wet...–1:99, Dry, 1:99...Wet
☞ Fx:10,
–100...+100
e: LFO Sync, e: Src, f: L Phase, f: R Phase
The LFO can be reset via a modulation source.
The "Src" parameter sets the modulation source that resets the
LFO. For example, you can assign Gate as a modulation source so
that the sweep always starts from the specified point.
"L Phase" and "R Phase" set the phase obtained when the left and
right LFOs are reset. In this way, you can create changes in pitch
sweep for the left and right channels individually.
The effect is off when a value of the modulation source spec-
ified in the "Src" parameter is 63 or smaller, and the effect is
Wet / Dry
on when the value is 64 or higher. The LFO is triggered and
reset to the "L Phase" and "R Phase" settings when the
value changes from 63 or smaller to 64 or higher.
Wet / Dry

47: St.DynamicDly

(Stereo Dynamic Delay)

This stereo delay controls the level of delay according to the
input signal level. You can use this as a ducking delay that
applies delay to the sound only when you play keys at a high
LFO, Dmod
velocity or only when the volume level is low.
Off...Tempo
Stereo In - Stereo Out
Left
☞,
0...30
Tri, Sine
Right
☞ Fx:20
Ctrl Target (Control Target)
Off, On
Selects from no control, output, and feedback
☞,
a
Pol (Polarity)
Off...Tempo
Reverses level control
Threshold
Sets the level to which the effect is applied
b
Offset
Sets the offset of level control
Attack
0...200
Sets the attack time of level control
c
Release
0...200
Sets the release time of level control
L Delay (L Delay Time)
d
0.0...500.0
Sets the delay time for the left channel
R Delay (R Delay Time)
e
0.0...500.0
Sets the delay time for the right channel
Feedback
f
Sets the feedback amount
HiDamp (High Damp)
Sets the damping amount in the high range
g
LoDamp (Low Damp)
Sets the damping amount in the low range
Spread
h
Sets the width of the stereo image of the effect sound
Off...Tempo
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
i
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
a: Ctrl Target
This parameter selects no level control, delay output control
(effect balance), or feedback amount control.
High Damp Low Damp
Delay
Feedback
High Damp Low Damp
Delay
FB
+
Attack, Release
Envelope
Threshold
Wet / Dry
Spread
Wet / Dry
Out
Control Target
None, Out, FB
+, –
0...100
0...100
1...100
1...100
0.0...680.0ms
0.0...680.0ms
–100...+100
0...100%
☞ Fx:43
0...100%
☞ Fx:43
–100...+100
☞ Fx:43
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100

Advertisement

Table of Contents
loading

This manual is also suitable for:

Micro x

Table of Contents