Korg MICROX X50 Parameter Manual: Multi 8: Insertfx; Setup

Music synthesizer and synthesizer/controller.
Hide thumbs

MULTI 8: InsertFX

☞For details on insert effects, refer to p.97 "6. Effect Guide."
8–1: BUS..8
8–2: BUS..16
Specifies the bus to which the program oscillator(s) of each
track 1–8, 9–16 will be sent. You can also set the amount of
signal that will be sent to the master effects.
8–1a
8–1(2)a: BUS Select, Send1(MFX1),
Send2(MFX2)
BUS Select
Specifies the output bus for the program oscillators of tracks
1–8 and 9–16.
The state of the settings can be viewed in the Setup page.
☞COMBI 8–1a
S1 (Send1(MFX1))
S2 (Send2(MFX2))
Here you can adjust the send levels from tracks 1–8, 9–16 to
master effects 1 and 2. This is valid when "BUS Select" is set
either to L/R or Off. If IFX is selected, the send level to the
master effects 1 and 2 is set by the ("S1 (Send1(MFX1))" and
"S2 (Send2(MFX2))" parameters located in the Setup page,
after the signal passes through IFX.
These settings have no effect if "BUS Select" is set to 1, 2 or
1/2.
If "Status" (2–1(2)a) is either INT or BTH, CC#93 and
#91 can be received to control send 1 and 2 respectively
and change their settings. If "Multi Mode" (GLOBAL
0–2a) is set to for Master, and you switch the multi set
number, these settings will be transmitted via MIDI for
tracks whose "Status" is EXT, EX2, or BTH. The set-
tings are transmitted and received on the MIDI channel
specified for each track by the "MIDI Channel" (2–1a/
2a) setting. The actual send level is determined by sum-
ming the value of these parameters with the send level
settings of the oscillator(s) of the program used by the
track ("S1 (Send1(MFX1))" and "S2 (Send2(MFX2))"
PROG 8–2a).
72
(BUS T01...08)
(BUS T09...16)
[DKit, L/R, IFX, 1, 2, 1/2, Off]
[000...127]
[000...127]
■ 8–1(2): UTILITY
☞"Write Multi" (0–1), "DKit IFX Patch" (COMBI 8–1)
Copy Insert Effect
☞PROG 8–1
However, the MIDI control channel specified in "Con-
trol Channel" of the 8: InsertFX, Setup page will not be
copied.
8–3: Setup
Here you can select the type of the insert effects, turn them
on/off etc.
8–3a
8–3c
8–3a: Insert FX Setup
IFX1
Insert Effect
Chain
Pan(CC#8)
BUS Select
S1 (Send1(MFX1))
S2 (Send2(MFX2))
These parameters are the same as in Program mode.
(☞PROG 8–2)
However, this differs from Program mode in that insert
effect dynamic modulation (Dmod) and the "Pan (CC#8),"
"Send1(MFX1)," and "Send2(MFX2)" which follow the
insert effect are controlled on the MIDI channel specified by
"Control Channel" (8–1b). The control changes used are the
same as in Program mode.
If the "Status" (2–1(2)a) is INT or BTH, receiving CC#8,
#93, or #91 will cause the post- insert effect pan and
send 1/2 to be controlled, changing the settings. If
"Multi Mode" (GLOBAL 0–2a) is set to for Master, and
you switch the multi set number, these settings will be
transmitted via MIDI on the "Control Channel" (8–1a)
for tracks whose "Status" is BTH, EXT, or EX2.
8–3b
[Off, On]
[00...89: name]
[
(Off),
(ON)]
[L000...C064...R127]
[L/R, 1, 2, 1/2, Off]
[000...127]
[000...127]

Advertising

   Also See for Korg MICROX X50

   Related Manuals for Korg MICROX X50

This manual also for:

Micro x

Comments to this Manuals

Symbols: 0
Latest comments: