Korg MICROX X50 Parameter Manual: Auto Reverse

Music synthesizer and synthesizer/controller.
Hide thumbs

42: Auto Reverse

This effect records the input signal and automatically plays it
in reverse (the effect is similar to a tape reverse sound).
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Right
D-mod
D
-mod
Input
Envelope Select
Rec Mode
a
Sets the recording mode
Reverse Time
b
Sets the maximum duration of the reverse playback
Envelope (Envelope Select)
Selects whether the start and end of recording is controlled via the
modulation source or the input signal level
c
Src (Source)
Selects the modulation source that controls recording when Enve-
lope is set to Dmod
Threshold
d
Sets the recording start level when Envelope is set to Input
Response
e
Sets the speed of the response to the end of recording
Direct Mix
f
Selects how a dry sound is mixed
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
g
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
a: Rec Mode, b: Reverse Time
When "Rec Mode" is set to Single, you can set up to 1320msec for
"Reverse Time." If recording starts during the reverse playback,
the playback will be interrupted.
When "Rec Mode" is set to Multi, you can make another record-
ing during the reverse playback. However, the maximum Reverse
Time is limited to 660msec.
If you wish to record a phrase or rhythm pattern, set "Rec Mode"
to Single. If you record only one note, set "Rec Mode" to Multi.
The "Reverse Time" parameter specifies the maximum duration
of the reverse playback. The part in excess of this limit will not be
played in reverse. If you wish to add short pieces of the reverse
playback of single notes, make the "Reverse Time" shorter.
Rec
Input
Rec Mode = Single
Rec Mode = Multi
c: Envelope, c: Src, d: Threshold
These parameters select the source to control the start and end of
recording.
When "Envelope" is set to Dmod, the input signal will be
recorded only when the value of the modulation source selected
by the Src parameter is 64 or higher.
When "Envelope" is set to Input, the input signal will be recorded
only when its level exceeds the Threshold level.
128
Direct
Auto Reverse
Mix
Rec/Reverse Play
Control
Envelope Control
Always On, Always Off, Cross Fade
Dry, 1:99...99:1, Wet
Rec Mode/Reverse Time
Reverse
Rec
Reverse
Envelope Select = Input
Time
Reverse Time
Reverse Time
When recording is completed, reverse playback starts immedi-
ately.
43: LCR Delay
Wet / Dry
This multitap delay outputs three Tap signals to the left, right,
and center respectively. You can also adjust the left and right
spread of the delay sound.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Wet / Dry
Left
Input Level D-mod
+
Single, Multi
Input Level D-mod
Right
20...1320ms
Dmod, Input
L Delay (L Delay Time)
☞,
Sets the delay time of TapL
a
Off...Tempo
Level
Sets the output level of TapL
C Delay (C Delay Time)
0...100
Sets the delay time of TapC
b
Level
0...100
Sets the output level of TapC
☞ Fx:31
R Delay (R Delay Time)
Sets the delay time of TapR
☞ Fx:31
c
Level
Sets the output level of TapR
C Fb (C Delay Feedback)
Off...Tempo
Sets the feedback amount of TapC
(Source)
d
–100...+100
Selects the modulation source of the TapC feedback amount
(Amount)
Sets the modulation amount of the TapC feedback amount
HiDamp (High Damp)
Sets the damping amount in the high range
e
LoDamp (Low Damp)
Sets the damping amount in the low range
InLvl Mod (Input Level Dmod [%])
Sets the modulation amount of the input level
f
Src (Source)
Selects the modulation source for the input level
Spread
g
Sets the width of the stereo image of the effect sound
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
h
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
e: HiDamp, e: LoDamp
These parameters set the damping amount of high range and low
range. The tone of the delayed sound becomes darker and lighter
as it feeds back.
g: Spread
This parameter sets the pan width of the effect sound. The stereo
image is widest with a value of 50, and the effect sound of both
channels is output from the center with a value of 0.
(L/C/R Delay)
L Delay
Level
C Delay
High Damp Low Damp
Level
Feedback
R Delay
Level
Wet / Dry
Spread
Wet / Dry
0...1360ms
0...50
0...1360ms
0...50
0...1360ms
0...50
–100...+100
Off...Tempo
–100...+100
0...100%
0...100%
–100...+100
☞ Fx:37,
Off...Tempo
☞ Fx:37
0...50
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100

Advertising

   Also See for Korg MICROX X50

   Related Manuals for Korg MICROX X50

   Related Content for Korg MICROX X50

This manual also for:

Micro x

Comments to this Manuals

Symbols: 0
Latest comments: