64: Comp-Ampsim; (Compressor - Amp Simulation); 65: Comp-Od/Hg; (Compressor - Overdrive/Hi.gain) - Korg MICROX X50 Parameter Manual

64: Comp–AmpSim
(Compressor – Amp Simulation)
This effect combines a mono-type compressor and an amp
simulation. You can change the order of the effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Compressor
EQ Trim LEQ HEQ
+
Right
Envelope - Control
[CMP] Sensitivity
a
Sets the sensitivity
Attack
Sets the attack level
b
Level (Output Level)
Sets the compressor output level
Pre EQ Trim
c
Sets the EQ input level
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ
d
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ
[AMP] Amplifier Type
e
Selects the type of guitar amplifier
[Routing]
f Switches the order of the compressor and amp simulation connec-
tion
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
g
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
65: Comp–OD/HG
(Compressor – Overdrive/Hi.Gain)
This effect combines a mono-type compressor and an over-
drive/high-gain distortion. You can change the order of the
effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Compressor
+
Right
Envelope - Control
[CMP] Sensitivity
a
Sets the sensitivity
Attack
Sets the attack level
b
Level (Output Level)
Sets the compressor output level
[OD] Mode (Drive Mode)
Switches between overdrive and high-gain distortion
c
Drive
Sets the degree of distortion
138
Routing
Amp Simulation
Comp Amp Simulation Filter
Output Level
SS, EL84, 6L6
→
AMP, AMP → CMP
CMP
Dry, 1:99...99:1, Wet
Routing
Overdrive / Hi-Gain
3 Band PEQ
Comp Driver
Output Level
Output Level
Mode: Overdrive / Hi-Gain
Drive
OverD, Hi-Gain
Level (Output Level)
Sets the overdrive output level
(Source)
d
Selects the modulation source for the overdrive output level
(Amount)
Sets the modulation amount of the overdrive output level
Lo (Low Cutoff)
Sets the center frequency for Low EQ (shelving type)
e
Wet / Dry
G (Gain)
Sets the gain of Low EQ
M1 (Mid1 Cutoff)
Sets the center frequency for Mid/High EQ 1 (peaking type)
Q
f
Sets the band width of Mid/High EQ 1
G (Gain)
Wet / Dry
Sets the gain of Mid/High EQ 1
M2 (Mid2 Cutoff)
Sets the center frequency for Mid/High EQ 2 (peaking type)
1...100
Q
☞ Fx:02
g
Sets the band width of Mid/High EQ 2
1...100
G (Gain)
☞ Fx:02
Sets the gain of Mid/High EQ 2
0...100
[Routing]
☞ Fx:02
h
Switches the order of the compressor and overdrive connection
0...100
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
–15...+15dB
(Source)
i
Selects the modulation source of the effect balance
–15...+15dB
(Amount)
Sets the modulation amount of the effect balance
66: Comp–P4EQ
(Compressor – Parametric 4-Band EQ)
Off...Tempo
This effect combines a mono-type compressor and a four-
band parametric equalizer. You can change the order of the
–100...+100
effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Right
[CMP] Sensitivity
a
Wet / Dry
Sets the sensitivity
Attack
Sets the attack level
b
Level (Output Level)
Sets the compressor output level
[PEQ] Trim
c
Sets the parametric EQ input level
Wet / Dry
[Routing]
d
Switches the order of the compressor and parametric EQ connection
B1 (Band1 Cutoff)
1...100
Sets the center frequency of Band 1
☞ Fx:02
Q
e
1...100
Sets the bandwidth of Band 1
☞ Fx:02
G (Gain)
0...100
Sets the gain of Band 1
☞ Fx:02
B2 (Band2 Cutoff)
Sets the center frequency of Band 2
Q
f
1...100
Sets the bandwidth of Band 2
☞ Fx:06
G (Gain)
Sets the gain of Band 2
Routing
Compressor Parametric 4Band EQ
Comp
Trim
Output Level
Envelope - Control
CMP → PEQ, PEQ → CMP
0...50
☞ Fx:06,
Off...Tempo
–50...+50
20...1.00kHz
–18...+18dB
300...10.00kHz
0.5...10.0
☞ Fx:06
–18...+18dB
500...20.00kHz
0.5...10.0
☞ Fx:06
–18...+18dB
CMP → OD, OD → CMP
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Wet / Dry
Wet / Dry
1...100
☞ Fx:02
1...100
☞ Fx:02
0...100
☞ Fx:02
0...100
20...1.00kHz
0.5...10.0
☞ Fx:06
–18...+18dB
50...5.00kHz
0.5...10.0
☞ Fx:06
–18...+18dB