07: St.para.4Eq; (Stereo Parametric 4-Band Eq) - Korg MICROX X50 Parameter Manual

Music synthesizer and synthesizer/controller
Hide thumbs Also See for MICROX X50:
Table of Contents

Advertisement

Level (Output Level)
Sets the output level
(Source)
e
Selects the modulation source for the output
level
(Amount)
Sets the modulation amount of the output level
Lo (Low Cutoff )
Sets the center frequency for Low EQ (shelving type)
f
G (Gain)
Sets the gain of Low EQ
M1 (Mid1 Cutoff)
Sets the center frequency for Mid/High EQ 1 (peaking type)
Q
g
Sets the band width of Mid/High EQ 1
G (Gain)
Sets the gain of Mid/High EQ 1
M2 (Mid2 Cutoff)
Sets the center frequency for Mid/High EQ 2 (peaking type)
Q
h
Sets the band width of Mid/High EQ 2
G (Gain)
Sets the gain of Mid/High EQ 2
Direct Mix
Sets the amount of the dry sound mixed to the distortion
i
SpSim (Speaker Simulation)
Switches the speaker simulation on/off
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
j
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
a: Wah
The Wah parameter switches the wah effect on/off.
a: (Sw)
This parameter sets how the wah effect is switched on and off via
the modulation source.
When "Sw" = Mmnt (Moment), the wah effect is usually turned
off. It is turned on only when you press the pedal.
When a value for the modulation source is less than 64,
"off" speed is selected, and when the value is 64 or higher,
"on" is selected.
When "(Sw)" = Tggl (Toggle), the wah effect is switched between
on and off each time you press the pedal.
The switch will be turned on/off each time the value of the
modulation source exceeds 64.
b: SweepRng, b: Src
This parameter sets the sweep range of the wah center frequency.
A negative value will reverse the direction of sweep. The wah cen-
ter frequency can be controlled by the modulation source speci-
fied in the "Src" parameter.
d: Drive, e: Level
The degree of distortion is determined by the level of input signal
and the setting of "Drive". Raising the "Drive" setting will cause
the entire volume level to increase. Use the "Level" parameter to
adjust the volume level. The "Level" parameter uses the signal
level input to the 3-Band EQ. If clipping occurs at the 3-Band EQ,
adjust the "Level" parameter.
d: Pre Low-cut
Cutting the signal in the low range before it is input to the Distor-
tion will create a sharp distortion.
g: Q, h: Q
These parameters set the bandwidth of each equalizer. The higher
the value, the narrower the band becomes.

07: St.Para.4EQ

0...50
☞,

(Stereo Parametric 4-Band EQ)

Off...Tempo
This is a stereo 4-band parametric equalizer. You can select
peaking type or shelving type for Band 1 and 4. The gain of
–50...+50
Band 2 can be controlled by dynamic modulation.
20...1.0kHz
Stereo In - Stereo Out
Left
–18...+18dB
300...10.00kHz
0.5...10.0
Right
–18...+18dB
D
-mod
500...20.00kHz
Trim
0.5...10.0
a
Sets the input level
B1 Type (Band1 Type)
–18...+18dB
b
Selects the type of Band 1
B4 Type (Band4 Type)
0...50
c
Selects the type of Band 4
B2 Dyn.G Src (Band2 Dynamic Gain Source)
Off, On
Selects the modulation source of the Band 2 gain
d
(Amount)
Dry, 1:99...99:1, Wet
Sets the modulation amount of Band 2 gain
B1 (Band1 Cutoff)
Off...Tempo
Sets the center frequency of Band 1
Q
–100...+100
e
Sets the bandwidth of Band 1
G (Gain)
Sets the gain of Band 1
B2 (Band2 Cutoff)
Sets the center frequency of Band 2
Q
f
Sets the bandwidth of Band 2
G (Gain)
Sets the gain of Band 2
B3 (Band3 Cutoff)
Sets the center frequency of Band 3
Q
g
Sets the bandwidth of Band 3
G (Gain)
Sets the gain of Band 3
B4 (Band4 Cutoff)
Sets the center frequency of Band 4
Q
h
Sets the bandwidth of Band 4
G (Gain)
Sets the gain of Band 4
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
i
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
b: B1 Type, c: B4 Type
Selects a filter type for Band 1 and 4.
Band1 Band2 Band3 Band4
PEQ
PEQ
PEQ
Trim
LEQ
LEQ
Trim
PEQ
PEQ
PEQ
Parametric 4EQ - Band1, Band4 Type
3dB
+Gain
Band4 Type=Shelving High
Band4 Type=Peaking
0dB
Band1 Type=Shelving Low
Band1 Type=Peaking
–Gain
3dB
Band1 Cutoff
Wet / Dry
PEQ
HEQ
HEQ
PEQ
Wet / Dry
0...100
Peaking, Shelving-Low
Peaking, Shelving-High
Off...Tempo
–18...+18dB
20...1.00kHz
0.5...10.0
☞ Fx:06
–18.0...+18.0dB
50...10.00kHz
0.5...10.0
☞ Fx:06
–18.0...+18.0dB
☞,
300...10.00kHz
0.5...10.0
☞ Fx:06
–18.0...+18.0dB
500...20.00kHz
0.5...10.0
☞ Fx:06
–18.0...+18.0dB
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Band4 Cutoff
107

Advertisement

Table of Contents
loading

This manual is also suitable for:

Micro x

Table of Contents