6-2: Mod. (Amp1 Modulation) - Korg MICROX X50 Parameter Manual

6–1c: AMS, Intensity
AMS (Pan AMS)
[Off, (PEG, FEG, AEG, LFO, KT, EXT)]
Indicates the source that will modify pan (☞p.152 "AMS
List"). This change will be relative to the "Pan (Amp1 Pan)"
setting.
Intensity
Specifies the depth of the effect produced by "AMS (Pan
AMS)."
For example, if "Pan (Amp1 Pan)" is set to C064 and "AMS
(Pan AMS)" is Note Number, positive (+) values of this
parameter will cause the sound to move toward the right as
the note numbers increase beyond the C4 note (i.e., as you
play higher), and toward the left as the note numbers
decrease (i.e., as you play lower). Negative (–) values of this
parameter will have the opposite effect.
■ 6–1: UTILITY
☞"Write Program" (0–1), "Copy Oscillator," "Swap Oscilla-
tor" (1–1)
6–2: Mod.
These settings allow you to apply modulation to amp 1 (for
oscillator 1) to modulate the volume.
6–2a
6–2b
6–2a: Keyboard Track
These parameters let you use keyboard tracking to adjust
the volume of oscillator 1. Use the "Key" and "Ramp"
parameters to specify how the volume will be affected by
the position on the keyboard of the note that you play.
Key (Keyboard Track Key):
Specifies the note number at which keyboard tracking will
begin to apply.
The volume will not change between "Low (KBDTrk Key
Low)" and "High (KBDTrk Key High)."
X50:
You can also input a value by playing a note on the
keyboard while you hold down the [ENTER] button.
Low (KBDTrk Key Low)
Keyboard tracking will apply to the range of notes below the
note number you specify here.
High (KBDTrk Key High)
Keyboard tracking will apply to the range of notes above the
note number you specify here.
Ramp (Ramp Setting):
Specifies the angle of the keyboard tracking.
22
[–99...+99]
(Amp1 Modulation)
6–2c
[C–1...G9]
[C–1...G9]
Low (KBDTrk Ramp Low)
With positive (+) values of this parameter, the volume will
increase as you play notes below the "Low (KBDTrk Key
Low)" note number. With negative (–) values, the volume
will decrease.
High (KBDTrk Ramp High)
With positive (+) values of this parameter, the volume will
increase as you play notes above the "High (KBDTrk Key
High)" note number. With negative (–) values, the volume
will decrease.
Volume change produced by key position and Ramp settings
Volume
Ramp Low=+99
Ramp Low=0
Ramp Low=–99
KBDTrk Low
6–2b: Amp Mod., LFO1 Mod., LFO2 Mod.
Indicates settings to specify how the volume of oscillator 1
will be controlled by velocity, OSC1 LFO1, and OSC1 LFO2.
Amp Mod. (Amp Modulation):
Velocity Int. (Amp Velocity Int.)
With positive (+) values, the volume will increase as you
play more strongly.
With negative (–) values, the volume will decrease as you
play more strongly.
Volume change (with positive (+) values of this parameter)
Note-on
Note-off
Softly played
LFO1 Mod. (LFO1 Modulation):
Intensity (LFO1 Intensity)
These parameters let you use "OSC1 LFO1" (3–1) to control
the oscillator 1 volume.
Negative (–) values will invert the LFO waveform.
LFO2 Mod. (LFO2 Modulation):
Intensity (LFO2 Intensity)
Specifies the depth and direction of the effect that "OSC1
LFO2"(3–2) will have on the volume of oscillator 1.
Negative (–) values will invert the LFO waveform.
6–2c: AMS, Int.
AMS (Amp AMS)
Indicates the source that will control the volume of amp 1
(☞p.152 "AMS List") (EXT) Velocity cannot be selected.
Int. (AMS Intensity)
Specifies the depth and direction of the effect that "AMS
(Amp AMS)" will have.
[–99...+99]
[–99...+99]
Ramp High=+99
Ramp High=0
Ramp High=–99
Key
KBDTrk High
[–99...+99]
Note-on
Note-off
Strongly played
[–99...+99]
[–99...+99]
[Off, (PEG, FEG, EXT)]
[–99...+99]