Filter/Dynamic; 00: No Effect; 01: St.amp Sim (Stereo Amp Simulation); 02: St.compressor (Stereo Compressor) - Korg MICROX X50 Parameter Manual

Filter/Dynamic

Filter and dynamics control effects

00: No Effect

Select this option when you do not wish to use any effects.
The Insert Effect section outputs unprocessed signals and the
Master Effect section mutes the output.
01: St.Amp Sim
(Stereo Amp Simulation)
This effect simulates the frequency response characteristics of
guitar amplifiers. It is also effective for organ and drum
sounds.
Stereo In - Stereo Out
Left
Right
Amplifier Type
a Select between three types of guitar amp simula-
tors
W/D (Wet/Dry)
Sets the balance between the effect and dry sounds
(Source)
b
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
02: St.Compressor
(Stereo Compressor)
This effect compresses the input signal to regulate the level
and give a "punchy" effect. It is useful for guitar, piano, and
drum sounds. This is a stereo compressor. You can link left
and right channels, or use each channel separately.
Stereo In - Stereo Out
Left
EQ Trim
Envelope Select
EQ Trim
Right
Envelope (Envelope Select)
a Determines whether the left and right channels are linked or used
separately
Sensitivity
b
Sets the sensitivity
Attack
c
Sets the attack level
104
Amp Simulation Filter
Amp Simulation Filter
SS, EL84, 6L6
Dry, 1:99...99:1, Wet
LEQ HEQ
Compressor
Output Level
Envelope - Control
Envelope - Control
Output Level
Compressor
LEQ
HEQ
L/R Mix, L/R Individually
Level (Output Level)
Sets the output level of the compressor
(Source)
d
Selects the modulation source for the compressor output level
(Amount)
Sets the modulation amount of the compressor output level
Pre EQ Trim
e
Sets the EQ input level
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ
f
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
g
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
a: Envelope
This parameter selects whether the left and right channels are
linked to control both signals simultaneously, or whether each
channel is controlled independently.
b: Sensitivity, d: Level
The "Sensitivity" parameter sets the sensitivity of the compressor.
If this parameter is set to a higher value, lower level sounds will
be boosted. With a higher Sensitivity, the overall volume level is
Wet / Dry
higher. To adjust the final volume level, use the "Level" parame-
ter.
Wet / Dry
c: Attack
This parameter controls the attack level.
Off...Tempo
–100...+100
03: St.Limiter
The Limiter regulates the input signal level. It is similar to the
Compressor, except that the Limiter compresses only signals
that exceed the specified level to lower unnecessary peak sig-
nals. The Limiter applies a peaking-type EQ to the trigger sig-
nal (which controls the degree of the Limiter effect), allowing
you to set any band width to be covered. This effect is a stereo
limiter. You can link left and right channels, or use each chan-
Wet / Dry
nel individually.
Stereo In - Stereo Out
Left
+
Wet / Dry
Right
☞
1...100
☞
1...100
☞
Compressor - Sensitivity
Level
Wet
Sensitivity=100
Sensitivity=40
Dry
Compressor - Attack
Level
Attack=80
Attack=20
Wet
Dry
(Stereo Limiter)
Limiter
Side PEQ
Envelope - Control
Trigger Monitor
Envelope - Control
Envelope Select
Limiter
0...100
☞,
Off...Tempo
–100...+100
0...100
–15.0...+15.0dB
–15.0...+15.0dB
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Time
Time
Wet / Dry
Gain Adjust
Gain Adjust
Wet / Dry