Korg MICROX X50 Parameter Manual page 9

microX:
Use the PROGRAM [A]–[GM] buttons to select
the bank. The microX provides rewritable banks A, B, C, D,
and E, each containing 128 programs (total 640). As for non-
rewritable program areas, it provides banks G (capital pro-
grams for GM), and bank g(d) (drums). If you press a PRO-
GRAM [A]–[GM] button, you will automatically enter
Program mode even if you had been in a different mode.
microX Bank List
Bank A
Bank B
for preloaded programs
Bank C
(for user programs)
Bank D
Bank E
Bank G GM capital program
Bank g(d) GM drums program
Bank G will toggle between the GM and g(d) banks each
time you press the PROGRAM [GM] button.
G→g(d)→G→g(d)→G...
Program Select
X50: [(A...D)0...127: name, (G, g(d))1...128: name]
microX: [(A...E)0...127: name, (G, g(d))1...128: name]
Here you can select a program.
Choose this parameter, and use one of the following meth-
ods to select a program.
X50:
• Turn the [VALUE] dial.
• Use the [INC][DEC] buttons.
• Use the numeric buttons [0]–[9] to enter a program
number, and press the [ENTER] button to finalize the
number.
• Press the center of the ClickPoint to highlight the field,
then use [π][†] to select a program, and press the
center to finalize your selection.
• 10's HOLD (☞p.2)
• Use PROG BANK [A]–[GM] to select a bank (☞p.1)
• Use "Select by Category" to select by category (☞p.2)
• Use the foot switch (☞p.80, 164)
• Receive a MIDI program change (☞p.171)
microX:
• Turn the [VALUE] dial.
• Press the center of the ClickPoint to highlight the field,
then use [π][†] to select a program, and press the
center to finalize your selection.
• Use "Select by Category" to select by category (☞p.2)
• Use the [CATEGORY] button and PROGRAM/
COMBINATION buttons to select by category (☞p.2)
• Use the foot switch (☞p.80, 164)
• Receive a MIDI program change (☞p.171)
You can receive MIDI program changes from a con-
nected external MIDI device, or use a foot switch to
select programs. (☞p.80 "Foot SW Assign" (GLOBAL
0–3a), p.164 "Foot Switch Assign List")
Category
Selects the program category.
All programs are classified into one of sixteen categories.
You can select the desired category, and then choose pro-
grams from that category.
To select a program by category, use the procedure
described below.
2
X50:
1 Press the [./HOLD] button to display
2 Use the ClickPoint [√][®][π][†] to choose "Category,"
3 Use the ClickPoint [√][®][π][†] to choose "Program
4 To cancel, press the [./HOLD] button twice to turn off the
Select by Category
1 Press the [CATEGORY] button to access the category
X50
microX
2 Use ClickPoint [√] to select "Prog/Category," and use
3 Use ClickPoint [π][†] to select a program. Alternatively,
4 Press the [MENU/OK] button to execute, or press the
microX:
1 Press the [CATEGORY] button to access the category
2 Note the categories shown below the PROGRAM buttons
[00...15: name]
3 Use the [VALUE] dial to select a program.
4 Press the [MENU/OK] button to execute, or press the
X50:
1 Press the [./HOLD] button to make the
To assign a category to each program, use the "Write
Program" (0–1) dialog box. To change the name of a cat-
egory, use "Category Name Prog. 00–07, 08–15"
(☞GLOBAL 3–1/2).
Cat. HOLD (Category Hold)
category will be held (fixed).
and use the [INC][DEC] buttons or the [VALUE] dial to
select a category.
Select," and use the [INC][DEC] buttons or the [VALUE]
dial to successively select programs in that category.
display.
If you press the [./HOLD] button in PROG 0: Play, the
selection will cycle in the order of
→ Cancel.
menu (Prog/Category).
Alternatively, you can access the category menu by
pressing the [UTILITY] button and choosing "Select by
Category" from the utility menu.
the [VALUE] dial to select a category.
use the ClickPoint [®] to choose "Sel (Select)," and use
the [VALUE] dial to select a program.
[EXIT/CANCEL] button if you decide not to execute.
Category & Bank
menu (Prog/Category).
or COMBINATION buttons, and press the corresponding
button for the desired category. You can also use the
[PAGE+][PAGE–] buttons to step through the categories
one by one.
[EXIT/CANCEL] button if you decide not to execute.
10's HOLD
cation appear.
. The
→
indi-