Korg MICROX X50 Parameter Manual Page 18

Music synthesizer and synthesizer/controller.
Hide thumbs

Advertisement

AMS (Pitch EG AMS)
Selects the source that will control the pitch modulation
applied by the pitch EG (☞p.152 "AMS List").
Intensity (AMS Intensity)
Specifies the depth and direction of the effect that "AMS
(Pitch EG AMS)" will have.
For example, if you set "AMS (Pitch EG AMS)" to Velocity
and set this value to +12.00, the velocity will control the
range of pitch change produced by the pitch EG in a range
of ±1 octave (☞p.154). As you play more softly, the pitch
change will draw closer to the pitch EG levels.
Pitch change (level)
Note-on
Note-on
Note-off
Note-off
Softly played
Strongly played with
(Intensity (Pitch EG) setting)
a positive (+) value
"Intensity" and "AMS (Pitch EG AMS)" will be
summed to determine the depth and direction of the
pitch modulation applied by the pitch EG.
2–1c: Portamento
This turns the portamento effect (smooth change in pitch
from one note to the next) on/off, and specifies how it will
be applied.
If you set Global 0–3a "Foot SW Assign" to Portamento SW
(CC#65) and turn a pedal switch connected to the ASSIGN-
ABLE SWITCH jack on/off, the portamento effect will be
applied according to these settings.
(☞p.164 "Foot Switch Assign List" Portamento SW (CC#65))
X50:
If [SW1] or [SW2] is set to Porta.SW (CC#65), using
SW1 or SW2 to turn portamento on/off will apply the set-
tings you specify here.
(☞p.152 "AMS List," ☞p.161 "SW1, SW2 Assign List" Prta.
SWCC#65)
Portamento will also be switched when CC#65 (Porta-
mento SW) is received.
Enable (Porta. Enable)
On (checked): Portamento will be applied.
Off (unchecked): Portamento will not be applied.
Fingered (Porta. Fingered)
This parameter is available when "Enable (Porta. Enable)" is
checked.
On (checked): Portamento will be applied when you con-
tinue holding the previous note as you press the next note
(legato playing).
Off (unchecked): Portamento will always be applied,
regardless of how you play.
Time (Porta. Time)
This parameter is available when "Enable (Porta. Enable)" is
checked.
This sets the portamento time. Increasing the value will pro-
duce a slower change in pitch.
■ 2–1: UTILITY
☞"Write Program" (0–1), "Copy Oscillator," "Swap Oscilla-
tor" (1–1)
[Off, (KT, EXT)]
2–2: OS1lfo
Specifies the amount of pitch change produced by LFO1 and
LFO2 for oscillator 1.
[–12.00...+12.00]
X50
microX
Note-on
Note-off
Strongly played with a
negative (–) value
2–2a: Pitch LFO1/2 Modulation
LFO1:
Intensity (LFO1 Intensity) [–12.00...+12.00]
Specifies the depth and direction of the pitch modulation
applied by the OSC 1 LFO1 settings you made in
"OS1LFO1" page (3–1).
With a setting of 12.00, a maximum of ±1 octave of pitch
modulation will be applied. Negative (–) values will invert
the LFO waveform.
X50:
Specifies the depth of pitch modulation that will be applied
by OSC1 LFO1 when you move the [MOD] up.
As you specify a higher value for this parameter, a greater
amount of pitch modulation will be applied by OSC1 LFO1
when you move the [MOD] wheel up (away from yourself).
With a setting of 12.00, a maximum of ±1 octave of pitch
modulation will be applied. Negative (–) values will invert
the polarity of the LFO.
[Off, On]
microX:
[Off, On]
Specifies the depth and direction of the effect that joystick
movement in the +Y direction (up) will have on the pitch
modulation applied by the OSC1 LFO1.
As this value is increased, moving the joystick in the +Y
direction will cause the OSC1 LFO1 to produce deeper pitch
modulation. With a setting of 12.00 a maximum of ±1 octave
of pitch modulation will be applied. Negative (–) values
will invert the LFO waveform.
AMS (LFO1 AMS)
[000...127]
Indicates the source that will control the depth of pitch mod-
ulation produced by the OSC1 LFO1 (☞p.152 "AMS List").
(OSC1 LFO)
2–2a
2–2a
Mod.Whl Int. (LFO1 Mod.Whl+Int.)
JS+Y Int. (LFO1 JS+Y Int.)
[Off, (PEG, FEG, AEG, KT, EXT)]
[–12.00...+12.00]
[–12.00...+12.00]
11

Advertisement

   Also See for Korg MICROX X50

   Related Manuals for Korg MICROX X50

This manual also for:

Micro x

Comments to this Manuals

Symbols: 0
Latest comments: