Korg MICROX X50 Parameter Manual: Prog 5: Ed–filter2; Basic; Mod.1 (filter2 Modulation1); Mod.2 (filter2 Modulation2)

Music synthesizer and synthesizer/controller.
Hide thumbs

Advertisement

AMS2 (Time Mod. AMS2)
I (AMS2 Intensity)
A (AMS2 SW Attack)
D (AMS2 SW Decay)
S (AMS2 SW Slope)
R (AMS2 SW Release)
These parameters are the settings for "AMS2" to control the
"Time" parameters of the filter 1 EG (☞"AMS1 (Time Moc.
AMS1)"–"R (AMS1 SW Release)").
■ 4–5: UTILITY
☞"Write Program" (0–1), "Copy Oscillator," "Swap Oscilla-
tor" (1–1)
For details on how to select the desired utility function, refer
to "PROG 0–1: UTILITY."
Sync Both EGs
Choose "Sync Both EGs" from the utility menu, and press
the center of the ClickPoint; a check mark will appear at the
left of "Sync Both EGs," and the "SYNC" icon will appear at
the left of the envelope curve in the display.
In this state, the filter 1 EG and the filter 2 EG can be edited
simultaneously. (Editing either one will cause the other to
change.)
"Sync Both EGs" cannot sync the filter EG and amp EG
independently. For example if you sync in 6–3d, it will
be synced here as well.
This can be selected only if "Mode (Oscillator Mode)"
(1–1a) is Double.
PROG 5: Ed–Filter2
5–1: Basic
5–2: Mod.1
(Filter2 Modulation1)
5–3: Mod.2
(Filter2 Modulation2)
5–4: lfoMod
(LFO Modulation)
5–5: EG
(Filter2 EG)
Indicates settings for filter 2, which controls the tone of oscil-
lator 2. You can select either a 24 dB/oct low pass filter with
resonance, or a 12 dB/oct low pass filter and 12 dB/oct high
pass filter connected in series. Filter 2 can be used when
"Mode (Oscillator Mode)" (1–1a) is Double. (☞"PROG 4:
Ed–Filter 1")
PROG 6: Ed–Amp1/2
[Off, (KT, EXT)]
[–99...+99]
[–, 0, +]
Here you can make settings for amp 1 which controls the
[–, 0, +]
volume of oscillator 1, and amp 2 which controls the volume
of oscillator 2. You can also specify the panning of each oscil-
[–, 0, +]
lator.
[–, 0, +]
6–1: Lvl/Pan
These parameters control the volume and pan of oscillator 1.
6–1a
6–1b
6–1a: Amp1 Level
Level (Amp1 Level)
Sets the volume of oscillator 1.
6–1b: Pan
Pan (Amp1 Pan)
Sets the pan (stereo location) of oscillator 1.
A setting of L001 places the sound at far left, C064 in the
center, and R127 to far right.
Random: The sound will be heard from a different location
at each note-on.
Use DKit Setting
This is valid when "Mode (Oscillator Mode)" (1–1a) is set to
Drums.
On (checked): The sound will be output at the "Pan" setting
that has been made for each key of the drum kit (GLOBAL
4–3a). When "Mode (Oscillator Mode)" is Drums, you will
normally use this setting.
Off (unchecked): All notes will be output as specified by the
"Pan (Amp1 Pan)" setting.
(Amp1 Level/Pan)
The volume of a program can be controlled by CC#7
(volume) and CC#11 (expression). The resulting level is
determined by summing the values of CC#7 and
CC#11. The Global MIDI channel "MIDI Channel"
(GLOBAL 1–1a) is used for control.
[Random, L001...C064...R127]
This can be controlled by CC#10 (panpot). A CC#10
value of 0 or 1 will place the sound at the far left, a
value of 64 will place the sound at the location specified
by the "Pan" setting for each oscillator, and a value of
127 will place the sound at the far right. This is con-
trolled on the global MIDI channel "MIDI Channel"
(GLOBAL 1–1a).
6–1c
[000...127]
[Off, On]
21

Advertisement

   Also See for Korg MICROX X50

   Related Manuals for Korg MICROX X50

This manual also for:

Micro x

Comments to this Manuals

Symbols: 0
Latest comments: