Korg MICROX X50 Parameter Manual: Controls; Combi 8: Ed–insertfx

Music synthesizer and synthesizer/controller.
Hide thumbs
7–5: Controls
X50
7–5a
microX
7–5a
7–5a: Knob B Assign
These settings assign functions (mainly various control
changes) to the B-mode of the REALTIME CONTROLS
knobs [1]–[4] (☞p.162 "Realtime Control Knobs B Assign
List").
The functions you specify here will be controlled when you
operate the REALTIME CONTROLS knobs [1]–[4] in B-
mode.
Since the REALTIME CONTROLS knob [1]–[4] function of
the B-mode assignments made for the programs assigned to
each timbre are not valid for the combination, new functions
must be set by these parameters.
Knob1–B (Knob1–B Assign)
Knob2–B (Knob2–B Assign)
Knob3–B (Knob3–B Assign)
Knob4–B (Knob4–B Assign)
X50:
7–5b: SW1/2 Assign
These settings assign the function of [SW1] and [SW2]
(☞p.161 "SW1, SW2 Assign List").
Since the function assignments of [SW1] and [SW2] made for
the programs assigned to each timbre are not valid for the
combination, new functions must be set for these parame-
ters.
SW1 (SW1 Assign)
SW1 Mode
SW2 (SW2 Assign)
SW2 Mode
☞PROG 7–3b
■ 7–5: UTILITY
☞"Write Combination," "Solo Selected Timbre" (0–1)
50
7–5b
[Off...MIDI CC#95]
[Off...MIDI CC#95]
[Off...MIDI CC#95]
[Off...MIDI CC#95]
[Off...Pitch Bend Lock]
[Toggle, Momentary]
[Off...Pitch Bend Lock]
[Toggle, Momentary]
COMBI 8: Ed–InsertFX
☞For details on insertion effects, refer to p.97 "6. Effect
Guide."
8–1: BUS
8–1a
8–1a: BUS Select, Send1(MFX1),
Send2(MFX2)
Here you can specify the output bus for each timbre 1–8.
You can also specify the send level to the master effects.
BUS Select
[DKit, L/R, IFX, 1, 2, 1/2, Off]
Specifies the output bus for the program oscillator of each
timbre 1–8. The current setting status can be viewed in the
8–2c: Routing Map.
DKit: This can be selected only if the program for which set-
tings are being made is a drum program "Mode (Oscillator
Mode) Drums" (PROG 1–1a). With a setting of DKit, the
"BUS Select" (GLOBAL 4–3a) setting made for each key of
the drum kit will be used.
For example if you have made "BUS Select" settings for each
key of a drum kit so that the Snare sounds are sent to IFX
and the other sounds are sent to L/R, selecting Dkit will
send the Snare sounds to IFX and the other sounds to L/R. If
you want to re-specify these routings, use Utility "DKit IFX
Patch" (8–1b).
If this is set to 1/2, the programs of timbres 1–8 will be
sent in stereo from (INDIVIDUAL OUTPUT) 1/2. If the
pan of the program oscillator is controlled by MIDI con-
trol change #10 (pan) or AMS (Alternate Modulation
Source), the sound will be output with the pan setting
that is in effect at the moment of note-on. Unlike the
case when this parameter is set to L/R, the pan of a
sounding note will not change in real-time.
If you wish to move the pan of a sounding note in real-
time and output it from (INDIVIDUAL OUTPUT) 1/2,
you must set "BUS Select" to IFX, select 00: No Effect
for "IFX" (8–2a), and then set "BUS Select" (8–2a) to 1/2.
S1 (Send1(MFX1))
S2 (Send2(MFX2))
For each timbre 1–8, these parameters set the send level to
master effects 1 and 2. These settings are valid when "BUS
Select" is set to L/R or Off. When IFX is selected, the send
levels to master effects 1 and 2 are set by the "S1
(Send1(MFX)), " "S2 (Send2(MFX))" parameters of the Setup
page (8–2a), after the sound has passed through IFX.
If "BUS Select" is set to 1, 2 or 1/2 these settings are ignored.
Control change #93 can be used to control the Send 1
level, and #91 to control the Send 2, and modify their
respective settings. These messages will be received on
the MIDI channel specified for each timbre in the 2: Ed–
Track Param, MIDI page.
The actual send levels are determined by summing this
[000...127]
[000...127]

Advertising

   Also See for Korg MICROX X50

   Related Manuals for Korg MICROX X50

This manual also for:

Micro x

Comments to this Manuals

Symbols: 0
Latest comments: