Modulation And Pitch Shift (Mod - Korg PA600 Reference Manual

38: St. Env. Phaser
(Stereo Envelope Phaser)
This stereo phaser uses an envelope generator for modulation.
You will obtain the same pattern of phasing each time you play.
You can also control the Phaser directly using the modulation
source.
Stereo In - Stereo Out
Left
Phaser
Phaser
Right
D-mod
D
-mod
Sweep Mode
EG Attack/Decay
EG
L Manu
0...100
Bottom
a
L Manu Top 0...100
R Manu
0...100
Bottom
b
R Manu Top 0...100
Sweep Mode EG, D-mod
c
Src Off...Tempo
EG Attack 1...100
d
EG Decay 1...100
e Resonance –100...+100
f High Damp [%] 0...100
-Wet, -
Wet/Dry 1:99...Dry...99:1
, Wet
g
Src Off...Tempo
Amt –100...+100
FX Amt
Resonance
High Damp
FX Amt
Sets the lower limit of the frequency
range for the effect on the left
channel
Sets the upper limit of the frequency
range for the effect on the left
channel
Sets the lower limit of the frequency
range for the effect on the right
channel
Sets the upper limit of the frequency
range for the effect on the right
channel
Determines whether the flanger is
controlled by the envelope
generator or by the modulation
source
Selects the modulation source that
triggers the EG (when EG is selected
for Sweep Mode), or modulation
source that causes the flanger to
sweep (when D-mod is selected for
Sweep Mode)
Sets the EG attack speed
Sets the EG decay speed
Sets the resonance amount
Sets the resonance damping
amount in the high range
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
Modulation and Pitch Shift (Mod./P.Shift)
Modulation and Pitch Shift (Mod./P.Shift)
39: Stereo Vibrato
This effect causes the pitch of the input signal to shimmer. Using
the AutoFade allows you to increase or decrease the shimmering
speed.
Stereo In - Stereo Out
Left
Right
LFO: Tri / Sine LFO Shape
AutoFade Fade-In Delay
a AUTOFADE Src Off...Tempo
Fade-In Delay
00...2000
[msec]
b
Fade-In Rate 1...100
LFO Waveform Triangle, Sine
c
LFO Shape –100...+100
LFO Frequency D-mod,
d
Mod AUTOFADE
LFO Frequency
0.02...20.00
[Hz]
e Src Off...Tempo
–20.00...
Amt
+20.00
MIDI Sync Off, On
MIDI,
BPM 40.00...
f
300.00
Base Note r...w
Times x1...x32
Depth 0...100
Src Off...Tempo
g
Amt –100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
h
Src Off...Tempo
Amt –100...+100
Effects
265
FX Amt
Vibrato
Vibrato
FX Amt
LFO Frequency
Selects the modulation source that
starts AutoFade
Sets the fade-in delay time
Sets the rate of fade-in
Selects the LFO Waveform
Changes the curvature of the LFO
Waveform
Switches between D-mod and
AUTOFADE for the LFO frequency
modulation
Sets the speed of the LFO
Selects a modulation source for LFO
speed
Sets the modulation amount of LFO
speed
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that specify
the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the depth of LFO modulation
Selects the modulation source of the
LFO modulation depth
Sets the modulation amount of the
LFO modulation depth
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source