THORLABS DCU223x Operation Manual And Sdk page 163

hCam
IS_AOI_IMAGE_GET_POS_Y_ABS
IS_AOI_IMAGE_GET_ORIGINAL_AOI
IS_AOI_IMAGE_SET_POS_FAST
IS_AOI_IMAGE_SET_POS_FAST_SUPPORTED
IS_AOI_AUTO_BRIGHTNESS_SET_AOI
IS_AOI_AUTO_BRIGHTNESS_GET_AOI
IS_AOI_AUTO_WHITEBALANCE_SET_AOI
IS_AOI_AUTO_WHITEBALANCE_GET_AOI
IS_AOI_MULTI_GET_SUPPORTED_MODES
IS_AOI_MULTI_SET_AOI
IS_AOI_MULTI_GET_AOI
IS_AOI_MULTI_MODE_X_Y_AXES
IS_AOI_MULTI_DISABLE_AOI
IS_AOI_SEQUENCE_GET_SUPPORT
ED
IS_AOI_SEQUENCE_SET_PARAMS
IS_AOI_SEQUENCE_GET_PARAMS
IS_AOI_SEQUENCE_SET_ENABLE
© 2013 Thorlabs GmbH
Camera handle
set for the X position. Sample 3 for AOI
Returns an object indicating whether
UINT
set for the Y position.
Returns the AOI in an
IS_RECT
scaling.
Allows changing the AOI position very quickly by using an
object. Hot pixel correction has to be disabled (see information above).
Returns an object indicating whether fast AOI position changes are
UINT
supported. The passed variable returns 0 if the function is not supported by
the sensor.
Sets the AOI for automatic brightness control (similar to
).
IS_AOI_IMAGE_SET_AOI
Returns the AOI for automatic brightness control (similar to
).
IS_AOI_IMAGE_GET_AOI
Sets the AOI for automatic white balance (similar to
).
IS_AOI_IMAGE_SET_AOI
Returns the AOI for automatic white balance (similar to
).
IS_AOI_IMAGE_GET_AOI
Returns the supported multi AOI modes in an
Sets the multi AOI mode. The mode you want to use has to be ORed with
.
IS_AOI_MULTI_SET_AOI
The axes are passed in an UINT array:
Array[0] - Array[3] = X1...X4
Array[4] - Array[8] = Y1...Y4
Sample 1 for multi AOI
Returns the set multi AOI mode. The mode that is used has to be ORed
with
IS_AOI_MULTI_SET_AOI
Sample 2 fo multi AOI
165
Multi AOI mode of the camera models DCC1240x/DCC3240x with up to
AOIs (up to 4 x and y axes). The axes are passed by a UINT array:
array[0] - array[3] = X1...X4
array[4] - array[8] = Y1...Y4
Attention: This parameter has been renamed in version 4.20. In formerly
versions this parameter was named IS_AOI_MULTI_MODE_AXES.
Disables Multi AOI. The mode that is used has to be ORed with
.
IS_AOI_MULTI_SET_AOI
Sample 3 for multi AOI
Returns a bitmask with the supported AOIs (only DCC1240x/DCC3240x
camera models)
Sample 1 for AOI sequence mode
Sets the parameters
162
camera models)
Sample 2 for sequence AOI mode
Returns the parameters
camera models)
Sample 2 for sequence AOI mode
Set a bitmask defining which AOIs should be active (only DCC1240x/
DCC3240x camera models).
Note: IS_AOI_SEQUENCE_SET_PARAMS must be called after
IS_AOI_SEQUENCE_SET_ENABLE, with enabling the sequence AOI
mode all AOIs are set to the same value and therefore the parameters are
lost.
Sample 3 for sequence AOI mode
164
IS_AOI_IMAGE_POS_ABSOLUTE
object without binning, subsampling or
UINT
165
.
165
165
of AOI 2, 3 or 4 (only DCC1240x/DCC3240x
166
of AOI 2, 3 or 4 (only DCC1240x/DCC3240x
162
166
166
4 Programming (SDK)
is
IS_POINT_2D
object.
161