Programming For Isdn Pri Dnis Type Call - Toshiba DK14 Programming Manual

ISDN
Guidelines for Programming ISDN Calling Features

Programming for ISDN PRI DNIS Type Call

The following table shows the minimum programming needed to make DNIS-type ISDN PRI calls
work in the Strata DK System.
Table 7-3 ISDN PRI DNIS Type Call Programming
Program
Number
03 XX 79
10-4 LED 9 On
16 XX 2
*
42 1 XX 1
*
43 1 1 24
*
63 2 04
*
64-1 1 LED 01 On
*
64-2 X
*
65-1 CO LED 001-023 On
*
66-1 1 01 1
*
01 LEDs 01-02, 11-12
On
01 LED 13 On
66-3
*
LED 14 On
LED 15 On
66-5 1 01 XXXX
*
66-6 1 01 LEDs 01~23 On
*
67-1 01 3
*
67-2 01 LEDs 01-04 On
*
*68-1 1 01 LEDs 01-03 On
68-2 01 XXX-XXX-XXXX
*
69-1 000-344 1 00
*
001- 023 LEDs 03~08
17
On
71-0 000 XXXX
7-8
Program Data
XX equals the slot in the DK system where the RPTU PCB is placed.
LDN registration will route the unknown number or call type in numbering
plan.
This tells the system that trunk group XX is an ISDN PRI trunk group.
This tells the system to make the ISDN PRI Span the span the primary
clocking source for the DK System. "XX" stands for the DK slot where the
RPTU PCB is placed, and the final "1" refers to circuit 1.
This tells the system that the D-Channel on the 1st ISDN PRI Span is the
24th channel on the PRI Span.
This tells the system how long to wait to collect digits from station users
making a ISDN PRI call before sending it to the network.
This tells the system to except the incoming calls on the PRI Span as DID or
DNIS calls.
"X" tells the system the number of digits to look for on a DID or DNIS call.
This tells the system that there are 23 bearer channels on the first Channel
Group and that they will appear on CO lines 001~023.
This tells the system that Trunk Group 01 is assigned to PRI Channel Group
(1).
This tells the system that Operator calls, Carrier Access, 1+10 Digit Dialing,
and Ring Back Tone to the outside caller are allowed.
This tells the system when interfaced with DMS XXX to send the Progress
Descriptor 81 or 83.
When connecting to a DMS XXX with NI1 protocol.
Set up message for outgoing call. When connecting to a DMS XXX. LED 11
must be Off in Program *66-3 when this LED is On.
This assigns the LDN/DID/DNIS number, the Q (asterisk) can be used as a
wildcard.
This assigns the CO lines to the index.
This tells the system that the PRI Span is for both way calling.
This tells the system to accept Speech, 3.1K Analog, 56K, and 64K type calls
on the ISDN PRI Span.
This tells the system to accept and send Calling Party Number on ISDN PRI
calls.
XXX-XXX-XXXX is the number you want the system to send out on an
outbound call for Caller Number Identification.
This tells the system to send the number entered in Program 68-2, as the
Calling Party Number Identification for all station on outbound calls.
This tells the system to accept DNIS calls on the ISDN PRI trunks 001~023
and to following DNIS Program 71 - 72, and show ANI if presented to the DK
system.
This tells the system that the incoming DNIS number XXXX is assigned to
DNIS address 000 in the DK system.
Description
Strata DK Programming 5/00