Programming For Isdn Pri Ldn Type Call - Toshiba DK14 Programming Manual

Table 7-3 ISDN PRI DNIS Type Call Programming (continued)
Program
Program Data
Number
71-1 000 XXXX

Programming for ISDN PRI LDN Type Call

The following table shows the minimum programming needed to make Listed Directory Number
(LDN)-type ISDN PRI calls work in the Strata DK System.
Table 7-4 ISDN PRI LDN Type Call Programming
Program
Program Data
Number
03 XX 79
10-4 LED 9 On
16 XX 2
*
42 1 XX 1
*
43-1 1 24
*
63-2 04
*
64 1 LED 01 Off
*
1 CO LEDs 001-023
65
*
On
66-1 01 1
*
01 LEDs 01-02, 11-12
On
01 LED 13 On
66-3
*
LED 14 On
LED 15 On
66-5 1 01 XXX-XXXX
*
1 01 CO LEDs
66-6
*
001~023 On
67-1 01 3
*
67-2 01 LEDs 01~04 On
*
68-1 01 LEDs 011~03 On
*
68-2 01 XXX-XXX-XXXX
*
Strata DK Programming 5/00
This tells the system to route the incoming DNIS call that was route to DNIS
address 000 to Station Port XXXX.
"XX" is the DK slot where the RPTU PCB is placed.
LDN registration will route the unknown number or call type in numbering
plan.
This tells the system that trunk group XX is an ISDN PRI Trunk Group.
This tells the system to make the ISDN PRI Span the Primary Clocking
Source for the DK System. XX equals the slot in the DK system where the
RPTU PCB is placed, and to look at circuit (1).
This tells the system that the D-Channel on the 1st ISDN PRI Span is the
24th channel on the PRI Span.
This tells the system how long to wait to collect digits from station users
making a ISDN PRI Call before sending it to the network.
This tells the system to except the incoming calls on the PRI Span as LDN
type calls.
This tells the system that there are 23 bearer channels on the first Channel
Group, and that they will appear on CO lines 001~023.
This tells the system that Trunk Group 01 is assigned to PRI Channel Group
1.
This tells the system that Operator Calls, Carrier Access, 1+10 Digit Dialing,
and Ring Back Tone to the outside caller are allowed.
This tells the system when interfaced with DMS XXX to send the progress
descriptor 81 or 83.
When connecting to a DMS XXX with NI1 protocol.
Set up message for outgoing call. When connecting to a DMS XXX. LED 11
must be Off in Program *66-3 when this LED is On.
XXX-XXXX tells the system what the LDN number is that the network will be
sending for the LDN Type Call for Trunk Group 01.
This tells the system to ring CO appearances 001~023 for incoming LDN
calls that match the LDN number that was entered in Program
Trunk Group.
This tells the system that the PRI Span is for both-way calling.
This tells the system to accept Speech, 3.1K Analog, 56K, and 64K type calls
on the ISDN PRI Span.
This tells the system to accept and send Calling Party Number on ISDN PRI
Calls.
XXX-XXX-XXXX is the number you want the system to send out on an
outbound call for Caller Number Identification.
Guidelines for Programming ISDN Calling Features
Description
Description
ISDN
66-5 for that
*
7-9