Honda Civic Service Manual page 670

72 mm Thrust Shim
t
Part Number
Thickness
23931 - P21 000 0.60 mm {0.0236 in}
2 3 9 3 2 - P 2 1 - 0 0 0 0.63 mm 10.0248 in)
c
23933 P21 - 000
0.66 mm (0.0260 in)
D
23934 - P21 000
0.69 mm (0.0272 in)
E 2 3 9 3 s - P 2 1 - 0 0 0
0.72 mm (0.0283 in)
F
2 3 9 3 6 - P 2 1 - 0 0 0 0.75 mm (0.0295 in)
G
23937 -P21-O00
0.78 mm (0.0307 in)
2 3 9 3 8 - P 2 1 - 0 0 0
0 . 8 1 m m ( 0 . 0 3 1 9 i n )
2 3 9 3 9 - P 2 1 - 0 0 0
0.84 mm (0.0331 in)
J
2 3 9 4 0 - P 2 1 - 0 0 0
0.87 mm (0.0343 in)
K
23941 P21 - 000
0.90 mm (0.0354 ini
L
23942 - P21 000
0.93 mm (0.0366 in)
2 3 9 4 3 - P 2 1 - 0 0 0 0.96 mm 10.0378 in)
N
23944 - P21 -000
0.99 mm (0.0390 in)
o
23945 - P21 000
1.02 mm (0.0402 in)
P
23946 - P21 000
1.05 mm (0.0413 in)
o 23947 - P2l 000
1.08 mm (0.0425 in)
R
2 3 9 4 8 - P 2 1 - 0 0 0
1.'1
'l mm (0.0437 in)
S
23949 - P21 000 1.14 mm (0.0449 in)
T
23950 - P21 000
1 . 1 7 m m ( 0 . 0 4 6 1 i n )
23951 - P21 -000 1.20 mm (0.0472 in)
23952 - P21 -000
1.23 mm (0.0484 in)
2 3 9 5 3 - P 2 1 - 0 0 0 1.26 mm (0.0496 in)
X
2 3 9 5 4 - P 2 1 - 0 0 0
1.29 mm (0.0508 in)
23955 - P21 -000
1.32 mm (0.0520 in)
z 2 3 9 5 6 - P 2 1 - 0 0 0
1.35 mm (0.0531 in)
2 3 9 5 7 - P 2 1 - 0 0 0
1.38 mm 10.0543 in)
AB
23958 - P21 -000
1.41 mm (0.0555 in)
AC
23959 P21 - 000 1.44 mm {0.0567 in)
23960 - P21 000
1.47 mm (0.0579 in)
AE
23961 - P21 -000 1.50 mm {0.0591 in)
23962 P21 - 000 1.53 mm {0.0602 in)
AG
2 3 9 6 3 - P 2 1 - 0 0 0
1 . 5 6 m m ( 0 . 0 6 1 1 i n )
AH
2 3 9 6 4 - P 2 1 - 0 0 0 1.59 mm {0.0626 in)
2 3 9 6 5 - P 2 1 - 0 0 0
'1.62 mm {0.0638 in)
2 3 9 6 5 - P 2 1 - 0 0 0
1.65 mm (0.0650 in)
AK
2 3 9 6 7 - P 2 1 - 0 0 0 1.68 mm {0.0661 in)
23968 - P21 -000 1.71 mm 10.0673 in)
23969 P21 - 000 1.74 mm {0.0685 in)
AN
2 3 9 7 0 - P 2 1 - 0 0 0 1.77 mm {0.0697 in)
AO
23971 - P21 -000 1.80 mm (0.0709 in)
7. lnstallthe thrust shim selected and oil guide plate in
the transmission housing.
72 mm THRUST
OIL GUIDE PLATE
TRANSMISSION
HOUSING
8 . I n s t a l l t h e s p r i n g w a s h e r a n d w a s h e r o n t h e b a l l
beaflng.
NOTE:
. Clean the spring washer, washer and thrust shim
throughly before installation.
.
I n s t a l l t h e s p r i n g w a s h e r , w a s h e r a n d t h r u s t
shim properlY.
-WASH€R
-<]>-.-'
x
-sPRtNG WASHER
-.-sK
( ( 9 r '
lnstallthe mainshaft in the clutch housing.
Place the transmission housing over the mainshaft
and onto the clutch housing.
Tighten the clutch and transmission housings with
several 8 mm bolts.
N O T E : l t i s n o t n e c e s s a r y t o u s e s e a l i n g a g e n t
between the housings.
8 x 1.25 mm
27 N.m (2.8 kgf.m. 20 lbf'ft)
Tap the mainshaft with a plastic hammer.
(cont'd)
9 .
1 0 .
' I l .
12.
1 3 - 8 9