Page 3
Safety: General • Observe all safety notes and precautions described in the Shop Manual in addition to those described in this Installation Instruction. Be extremely careful for your safety and safety of others particularly. • Be careful not to damage the vehicle and the parts. •...
PARTS LIST LHD Fog Light Kit Fog lights (2) Harness A Harness B Combination light switch Relay Wire ties (21) 20A Fuse 5 x 14 mm Self-tapping screws (4) (Some may not used) Clip Wire tie with clip A Wire tie with clip B 5 x 16 mm Self-tapping screws (2) Aluminum tapes (5)
Page 5
RHD Fog Light Kit Fog lights (2) Harness A Harness B Combination light switch Relay Wire ties (21) 20A Fuse Wire tie with clip (Some may not used) 5 x 14 mm 5 x 16 mm Wire tie with holder Aluminum tapes (5) Self-tapping screws (4) Self-tapping screws (2)
Page 7
INSTALLATION Removing the Vehicle Parts • LHD models How to Use the Contact Cleaner To step 3 • Using contact cleaner on a shop towel, thoroughly • RHD models clean the areas where the accessories will be attached. To step 12 NOTICE <LHD models>...
Page 11
17. Remove the upper column cover. 20. Open the hood. 21. Attach the tapes to protect the vehicle. 2 HOOKS NOTICE 2 RETAINING TABS • Do not remove the tapes until after the reinstallation. HEADLIGHT QA52705AK 18. Remove the self-tapping screws. TAPES FRONT BUMPER QA22406CH...
Page 12
24. Remove the short clips and long clips. 26. Release the retaining tabs and clips. CLIP HANDY REMOVER 4 CLIPS SHORT SHORT CLIP CLIP 6 LONG CLIPS QA22407BH 25. Remove the short clip and long clip. 2 RETAINING TABS QA22404BH 27.
Page 13
29. Release the retaining tabs. 32. Release the front bumper. PARKING SENSOR CONNECTOR 2 DRL LIGHT (if equipped) CONNECTORS HEADLIGHT 3 RETAINING TABS FRONT BUMPER QA22408BH 30. Release the retaining tabs. FRONT BUMPER QA52001BK 33. Remove the front bumper. NOTICE 7 RETAINING •...
Page 14
• Diesel • LHD models To step 34 To step 35 • Petrol • RHD models To step 35 To step 36 <Diesel> <LHD models> 34. Remove the air duct. 35. Turn down the left inner fender. 4 CLIPS LEFT INNER 4 CLIPS FENDER 2 BOLTS...
Page 15
Installing the fog light 39. Install the left bracket. 37. Remove the left cover. FRONT BUMPER (inside) FRONT BUMPER (outside) LEFT BRACKET 5 x 16 mm SELF-TAPPING SCREW QA41803AK LEFT COVER 5 RETAINING 40. Remove the self-tapping screw. QA41801AK TABS 38.
Page 16
Routing the Harness B (LHD) 41. Install the fog light. 43. Connect the harness B connector. SELF-TAPPING SCREW HARNESS B FOG LIGHT 2 SELF-TAPPING SCREWS, 5 x 14 mm (supplied) QA41804AK HARNESS B 1-PIN CONNECTOR 42. Repeat same procedures for the other side. TAPE (Remove.) Repeat steps 37 through 41.
Page 17
• Without sub-fuse box • Diesel To step 45 To step 47 • With sub-fuse box • Petrol To step 46 To step 50 <Without sub-fuse box> <Diesel> 45. Secure the harness B. 47. Secure the harness B. 48. Secure the harness B ground terminal. VEHICLE PANEL WIRE TIE...
Page 18
<Petrol> 53. Secure the harness B. 50. Secure the harness B. 51. Secure the harness B ground terminal. BUMPER GREEN TAPE GREEN TAPE BEAM VEHICLE WIRE TIE HARNESS B HARNESS WIRE HARNESS B GROUND TERMINAL HARNESS B VEHICLE GROUND QA52406BK TERMINAL VEHICLE GROUND BOLT...
Page 19
55. Secure the harness B. 57. Connect the harness B connectors. 58. Reinstall the front bumper. 2 HARNESS B 2 HARNESS B GREEN TAPE HARNESS B 2-PIN CONNECTORS 2-PIN CONNECTORS BUMPER BEAM FOG LIGHT WIRE TIE QA52407AK FRONT BUMPER QA52750AK FOG LIGHT 56.
Page 20
60. Drill the lower column cover. • Without other accessory harness To step 63 • With other accessory harness To step 64 <Without other accessory harness> 63. Connect the harness A connectors. DRILL 6-PIN 3 mm 9 mm CONNECTOR 4-PIN DRILL BIT CONNECTOR HARNESS A...
Page 21
66. Release the vehicle connectors. <With other accessory harness> 64. Connect the harness A connectors. 6-PIN CONNECTOR HARNESS A 6-PIN CONNECTOR CLIP VEHICLE CONNECTORS FUSE BOX QA72002AK FUSE BOX 67. Disconnect the vehicle connector. OTHER ACCESSORY HARNESS A HARNESS 4-PIN 4-PIN CONNECTOR CONNECTOR...
Page 22
68. Insert the harness A terminal. 71. Route the harness A. 69. Reinstall the vehicle connector. RETAINER (Unlock.) SMALL FLAT-TIP SCREWDRIVER VEHICLE 28-PIN CONNECTOR HARNESS A TERMINAL CONNECTING LOCATION After the terminal insertion, lock the retainer. HARNESS A QA52502AK 72. Route the harness A. <HARNESS SIDE VIEW>...
Page 23
73. Secure the harness A. 75. Install the combination light switch. VEHICLE HARNESS 2 WIRE TIES GREEN COMBINATION TAPE LIGHT SWITCH (supplied) HARNESS A VEHICLE CLIPS QA52503AK 2 RETAINING TABS (Push.) QA52302AK 74. Remove the combination light switch. 76. Connect the harness A connectors. HARNESS A VEHICLE 12-PIN CONNECTOR...
Page 24
77. Secure the harness A. 78. Reinstall the lower column cover. 79. Secure the harness A. NOTICE • Check that the harness is secured without undue strain to the connector cord. LOWER COLUMN COVER CONNECTOR CORD (without undue strain) HARNESS A VEHICLE CLIP 3 WIRE <With other accessory harness>...
Page 25
81. Attach the fuse label. 83. Route the harness B. DRIVER’S DASHBOARD LOWER COVER HARNESS B 1-PIN CONNECTOR FUSE LABEL (20A OPTION FUSE) FUSE LABEL QA71201AK To step 118 Routing the Harness B (RHD) HARNESS B QA41807BK 82. Secure the harness B. 84.
Page 26
85. Secure the harness B. 87. Route the harness B. 88. Secure the harness B. VEHICLE HARNESS VEHICLE CLIP GREEN TAPE BUMPER BEAM WIRE 2 WIRE TIES 2 WIRE TIES HARNESS B QA42201BK 86. Secure the harness B. QA42501BK 89. Secure the harness B. <SECTION VIEW>...
Page 27
<Petrol> • Diesel 93. Secure the harness B. To step 90 94. Secure the harness B ground terminal. • Petrol To step 93 <Diesel> 90. Secure the harness B. 91. Secure the harness B ground terminal. WIRE TIE VEHICLE HARNESS HARNESS B GROUND WIRE TIE...
Page 28
96. Connect the harness B connectors. • Without other accessory harness 97. Reinstall the front bumper. To step 99 • With other accessory harness To step 100 <Without other accessory harness> 99. Connect the harness A connectors. 2 HARNESS B 2 HARNESS B 2-PIN CONNECTORS 2-PIN CONNECTORS...
Page 29
103. Insert the harness A terminal. <With other accessory harness> 104. Reinstall the vehicle connector. 100. Connect the harness A connectors. RETAINER (Unlock.) HARNESS A 4-PIN 6-PIN CONNECTOR CONNECTOR SMALL FLAT-TIP SCREWDRIVER After the terminal insertion, VEHICLE lock the retainer. 13-PIN CONNECTOR FUSE BOX...
Page 30
106. Attach the wire tie with holder. 109. Route the harness A. 110. Secure the harness A. WIRE TIE WITH HOLDER 3 WIRE TIES STEERING HANGER BEAM QA52004BK 107. Secure the harness A relay block. 108. Secure the harness A. GREEN VEHICLE TAPE...
Page 31
112. Remove the combination light switch. 114. Connect the harness A connectors. HARNESS A VEHICLE 12-PIN CONNECTOR COMBINATION HARNESS A LIGHT SWITCH 12-PIN CONNECTORS VEHICLE 12-PIN CONNECTOR QA52303AK 115. Secure the harness A. NOTICE 2 RETAINING • Check that the harness is secured without undue TABS (Push.) strain to the connector cord.
Page 33
Check After Installation 122. Check the operation of the fog lights. To turn on the Front Fog lights only 120. Check that all parts are routed and installed • Turn the lights switch to the “ ” or “ ” position. properly.
Reinstalling the All Removed Parts Aiming Adjustment 123. Reinstall all removed parts. The illustration shows information on the left side of the vehicle. Repeat the same procedure for the right side of NOTICE the vehicle. • When you connect the connector, be sure to 127.
MAINTENANCE 132. Adjust the aim at the adjust point if the aiming is not according to the indicated measurement. Bulb Replacement NOTICE The illustration shows information on the left side of the • Adjust so that the lighting is below the specified vehicle.
Page 36
QA71902AK Install the new bulb to the fog light. NOTICE • Use only the genuine Honda parts. Rating: 12V 55W H11 Bulb • Make sure that the bulb is properly installed. • Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on.