Table of Contents CHAPTER 1 PREFACE..........................1-1 ............................1-1 BOUT UIDE .............................. 1-1 ERMS SAGE CHAPTER 2 PRODUCT INTRODUCTION ....................2-1 ..........................2-1 RODUCT NTRODUCTION ............................... 2-1 RONT ANEL ..............................2-2 ANEL CHAPTER 3 HARDWARE INSTALLATION ....................3-1 CHAPTER 4 USING THE WEB USER INTERFACE .................
Page 3
MSTP ................................6-6 MSTP Global Configuration ............................ 6-8 MSTP Timers Configuration ............................ 6-9 CIST Settings ................................. 6-10 MSTP VLAN Mapping ............................6-11 MSTP Port Settings ..............................6-11 MSTP CIST Port Status ............................6-11 RSTP ................................. 6-12 RSTP Global Configuration ........................... 6-12 RSTP Configuration ...............................
Page 4
RMON E ........................9-7 VENTS ONFIGURATION CHAPTER 10 SWITCH STATISTICS ..................... 10-9 ..........................10-9 WITCH TATISTICS ..........................10-9 NTERFACE TATISTICS ..........................10-10 THERNET TATISTICS VLAN S ............................. 10-10 TATISTICS MSTP ..............................10-11 MSTP Information ............................... 10-11 MSTP CIST Port Statistics ........................... 10-11 MSTP MSTI Port Statistics ..........................
Page 5
........................13-1 CCOUNT OMMAND ..............................13-1 USERNAME ............................... 13-1 SHOW USERS ..............................13-2 LISTUSER CHAPTER 14 MANAGEMENT VLAN COMMAND ................... 14-1 VLAN C ......................14-1 ANAGEMENT OMMAND ..........................14-1 MANAGEMENT VLAN LIST ........................... 14-1 SHOW MANAGEMENT VLAN CHAPTER 15 IP SETTINGS COMMAND ....................15-1 IP S ........................
Page 6
CHAPTER 19 SSL COMMAND ......................19-1 SSL C ............................ 19-1 OMMAND ............................19-1 IP HTTP SECURE ..............................19-2 DEBUG SSL ..........................19-3 SHOW SSL SERVER CERT ......................19-4 SHOW IP HTTP SECURE SERVER STATUS CHAPTER 20 SYSTEM LOG COMMAND ..................... 20-1 ........................
................................26-1 VLAN ....................... 26-1 SWITCHPORT ACCEPTABLE FRAME TYPE ........................26-2 SWITCHPORT INGRESS FILTER ............................26-2 SWITCHPORT PVID ................................ 26-3 PORTS ..............................26-4 DEBUG VLAN ..............................26-4 SHOW VLAN ..........................26-7 SHOW VLAN DEVICE INFO ..........................26-8 SHOW VLAN PORT CONFIG CHAPTER 27 DYNAMIC VLAN COMMAND ..................
Page 8
........................30-2 PORT CHANNEL LOAD BALANCE ............................30-3 CHANNEL GROUP ........................... 30-3 LACP PORT PRIORITY ............................. 30-4 LACP TIMEOUT ............................30-4 LACP WAIT TIME .......................... 30-5 SHUTDOWN PORT CHANNEL ..........................30-5 SHOW ETHERCHANNEL ..............................30-9 SHOW LACP ......................30-10 SHOW INTERFACES ETHERCHANNEL CHAPTER 31 802.1X COMMAND ......................
Page 9
......................33-3 ADDRESS TABLE STATIC UNICAST ......................... 33-4 SHOW MAC ADDRESS TABLE ....................... 33-4 SHOW MAC ADDRESS TABLE AGING TIME ......................33-5 SHOW MAC ADDRESS TABLE COUNT ..................33-5 SHOW MAC ADDRESS TABLE DYNAMIC MULTICAST ..................... 33-6 SHOW MAC ADDRESS TABLE DYNAMIC UNICAST .....................
Page 10
........................40-2 COSQ SCHEDULING ALGORITHM ........................40-3 SWITCHPORT PRIORITY DEFAULT ........................40-3 SHOW VLAN TRAFFIC CLASSES ..........................40-4 SHOW VLAN PORT CONFIG ..............................40-5 SHOW DSCP ..........................40-5 SHOW COSQ ALGORITHM CHAPTER 41 RMON COMMAND ......................41-1 RMON C ..........................41-1 OMMAND ..............................
Preface About This Guide This guide provides instructions on how to install and configure the TL2-G244 24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots. This guide is mainly divided into four parts: 1. Hardware Installation: Step-by-step hardware installation procedure.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 3 Hardware Installation This chapter provides unpacking and installation information for TL2-G244. Unpacking Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Manual to make sure all items are present and undamaged.
Page 15
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots rack. Figure 3 – Mount the Switch in the rack or chassis Safety Instructions Caution A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 4 Using the Web User Interface After a successful physical installation, you can configure the Switch, monitor the network status, and display statistics using a web browser. Supported The embedded Web-based Management currently supports the following web Browsers browsers: A) Internet Explorer 6 or higher...
Page 17
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 7 – Enter the IP address 192.168.10.200 in the web browser The default user name and password are: Note User Name Password Privilege admin admin guest guest123 After login successfully, following page will appear. Device Status Figure 8 –...
Page 18
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots The Device Status provides a real-time switch port link status. By choosing different functions in the Function Tree, you can change all the settings in the Main Configuration Screen. The main configuration screen will show the current status of your Switch by clicking the model name on top of the function tree.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 5 Configuring System Basic Functions System Basic Function List System Information User Account Management VLAN Management IP Settings IP Authorized Manager SNMP SNMP User/Group Table Configuration SNMP Group Access Table Configuration SNMP View Table Configuration SNMP Community Settings...
The hardware version of this device. Firmware Version The firmware version of the device. Device Name The name of the device. Default is TL2-G244. Device Contact The identification information of a contact person. Default is SysContact. Device Location Entering the device location description. Maximum of 50 characters is allowed and a null string is not accepted.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 11 – System > Management VLAN Parameter Description Management VLAN The VLAN ID of management VLAN. It can be a single VLAN ID from 1 to 4094, a range of VLAN IDs separated by a hyphen (-) ,or a series of non-continuous numbers divided by a comma (,) Click ADD to submit the changes and the Remove button will remove an existed VLAN ID.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 13 – System > IP Authorized Manager Parameter Description IP Address IP address of authorized manager Subnet Mask Subnet mask of the authorized IP address Port List (Incoming) Interface of the authorized administrator is allowed to connect to VLANs Allowed VLAN ID of the authorized administrator is allowed to connect to.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots SNMP Version Specify the SNMP version to be used, which can be v1, v2c, or v3. Select ‘encrypted’ if the encryption for user authentication is needed. Once the encryption is enabled, then you can set the authentication and privilege algorithm and passwords.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots SNMP View Table Configuration This page is to create a SNMP view, which limits the range of MIB objects that a SNMP administrator can access to. Figure 16 – System > SNMP > View Table Parameter Description View Name...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Click ADD to submit the changes and the Reset button will clear the information. Select and click Delete to remove an existed entry. SNMP Host Table This page is to create a host that can access the device by SNMP protocol. Figure 18 –...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 20 – System > SSH Parameter Description SSH Status Select Enable or Disable to turn on or off the SSH server function. Default is enabled. Version Specify the SSH version supported. V2 –...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots System Log Configuration This page is to configure system log settings. Figure 22 – System > System Log Parameter Description Syslog Status The status of syslog server function. Default is enabled. Time Stamp Specifies if time stamp is attached with syslog messages.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 23 – System > SNTP > Time Settings Parameter Description Current Time Current system time. SNTP Status To enable/disable the Simple Network Time Protocol (SNTP) function. Default is disabled. SNTP Poll Interval in To set the time interval that SNTP synchronizes the time on SNTP server, and Seconds (30-86400)
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots (Month:Day:HH:MM) Click Apply to submit the changes. Configuration Save Configuration This page is used to save the running configuration. Figure 25 – System > Configuration > Save Parameter Description Save option Options to save the running configuration: Flash Save: Save to the device’s flash memory with a designated file name.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Parameter Description Restore Option Options to restore the startup configuration: No Restore: Applying this option will reset the NV-RAM to default settings. Note: This will only reset the settings in NV-RAM, not the entire device configuration.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Reboot This page is to reboot the system. Figure 28 – System > Reboot Click Reboot to warm start the device. If the Switch reboots without write the running configurations, the last Note configuration wrote in NV-RAM will be loaded.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 6 Configuring Layer 2 Management Functions Layer 2 Management Function List Port Manager Port Basic Settings Port Monitoring Port Control VLAN VLAN Basic Information VLAN Port Settings Static VLAN Configuration ...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Port Manager Port Basic Settings This page is to configure basic settings of switch ports. Figure 29 – Layer2 Management > Port Manager > Basic Settings Parameter Description Port Specify the switch port to be configured. Link State Display the physical connection states of the port.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 30 – Layer2 Management > Port Manager > Port Monitoring Parameter Description Status To enable/disable the port monitoring session on the device. Default is disabled. Monitoring Port Specify the source port of the mirror session. Port Specify the destination port of the mirror session.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 31 – Layer2 Management > Port Manager > Port Control Parameter Description Port Specify the switch port to be configured. Mode To enable/disable auto-negotiation function on ports. Default is Auto. Duplex To set the port duplex mode.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 32 – Layer2 Management > VLAN > Basic Information Parameter Description VLAN Mode Choose from 802.1Q VLAN or Asymmetric VLAN modes. Default is 802.1Q VLAN. Maximum VLAN ID Display the maximum VLAN ID can be configured. Default is 4094. Maximum Supported Display the maximum VLANs can be supported.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Acceptable Frame To configure the acceptable frame type of a port. Types All: Accepts all kinds of frames. Tagged: Accepts only tagged frames UnTagged and Priority Tagged: Accepts only untagged frames and frames with priority tag.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 35 – Layer2 Management > Dynamic VLAN > Dynamic VLAN Global Configuration Parameter Description Garp System Control Choose Start to enable GARP function, and Shutdown to disable it. It is needed for using dynamic VLAN function.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots GARP Timers Configuration This page is to set the GARP timers on an interface. Figure 37 – Layer2 Management > Dynamic VLAN > Port Settings Parameter Description Port No Specify the switch port to be configured. GarpJoinTime Specify the join time of GARP.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 38 – Layer2 Management > MSTP > Global Configuration Parameter Description System Control To activate or shutdown the MSTP function. Select Start to activate the MSTP function, Shutdown to shutdown MSTP function. MSTP Status To enable or disable the MSTP.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots is 20. Forward Delay Specify the time period in second that a port changes the STP state from blocking to forwarding. The possible value is 4-30. Default is 15. Transmit Hold Count Specify the hold counter to limit maximum transmission rate of the Switch.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots root port. Select True to enable the root guard function, False to disable it. Default is false. Restricted TCN To enable the topology change guard function to prevent the topology change caused by this port.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 43 – Layer2 Management > MSTP > CIST Port Status Click 1-12, 13-24 to display the statistics for corresponding ports. RSTP RSTP Global Configuration This page is to configure the RSTP global settings. Figure 44 –...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 45 – Layer2 Management > RSTP > Basic Settings Parameter Description Priority Specify the bridge priority of spanning tree. Default is 32768. Version Select the spanning tree compatibility version. The possible options are STP Compatible or RSTP Compatible.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Select Select a port to apply the changes. Port Port ID. Port Role Specify the current role of the port. Port Priority Specify the spanning tree port priority. Possible value is 0-240. Default is 128. RSTP Status To enable or disable the RSTP on this port.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 48 – Layer2 Management > LA > Basic Settings Parameter Description System Control To activate or shutdown link aggregation function of the Switch. Select Start to activate link aggregation function, Shutdown to shutdown it. Default is Start.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 50 – Layer2 Management > LA > Port Channel Settings Parameter Description Port Channel ID Select a configured port channel group to submit the changes. Action Type To add or delete ports from/to a port channel. Select Add to add ports, Delete to delete one.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Select Select a port to submit the changes. Port Port ID. Port Priority Specify the link aggregation port priority of this port. Possible values are 0-65535. Default is 128. Port Identifier Port ID.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots 802.1X 802.1X Basic Settings This page is used to configure the 802.1X authentication global settings. Figure 54 – Layer2 Management > 802.1X > Basic Settings Parameter Description System Control To activate or shutdown 802.1X function of the Switch. Select Start to activate the function, Shutdown to shutdown it.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Select Select a port to apply the configuration changes. Port Port ID. Port Control To set the authenticator control on this port. The possible options are: ForceUnauthorized - All traffic is blocked to the port. Auto - Enable the 802.1X authentication on this port, and the port authorized or unauthorized will based on the 802.1X authentication result.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Select Select a port to apply the configuration changes. Port Port ID. Quiet Period (secs) The period that Switch will not do anything after a failed authentication. Possible value is 0-65535 seconds. Default is 60. Transmit Period (secs) The period that Switch waits for a response to an EAP-request/identity frame from the client before retransmitting the request.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots RADIUS Server Configuration This page is to configure the details of RADIUS server. Figure 58 – Layer2 Management > 802.1X > Radius Settings Parameter Description Server ID Specify the new RADIUS server ID. The possible ID is 1-10. IP Address Specify the IP address of the new RADIUS server.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots IGMP Snooping IGMP Snooping Configuration This page is to configure the IGMP Snooping global settings. Figure 59 – Layer2 Management > IGMP Snooping > Basic Settings Parameter Description System Control To activate or shutdown IGMP snooping of the Switch.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 60 – Layer2 Management > IGMP Snooping > Timer Configuration Parameter Description Router Port Purge To set the time-out period that an IGMP multicast router port hasn’t received Interval (60~600 Secs) IGMP router control packet, it will be deleted.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots IGMP Snooping VLAN Router Ports This page is to display the static and dynamic learned IGMP router ports of each VLAN. Figure 62 – Layer2 Management > IGMP Snooping > Router Ports MAC Based Multicast Forwarding Table This page is to display the IGMP group MAC address was learned.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Parameter Description Select Select which MAC address to apply the configuration changes. VLAN ID VLAN ID of this MAC address belongs to. MAC Address The MAC address. Allowed Port Specify the port allowed to forward the MAC address. Status Specify the attribute of this static MAC.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Port Security Settings This page is to configure the port security function for each port. Figure 66 – Layer2 Management > Static MAC Entries > Port Security Settings Parameter Description Select Select a port to apply the configuration changes.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 7 Configuring ACL Functions ACL Function List MAC ACL Configuration IP Standard ACL Configuration IP Extended ACL Configuration Classmap Settings Policymap Settings MAC ACL Configuration This page is to create/configure a rule to MAC Access Control List.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 68 – ACL > IP Standard ACL Parameter Description ACL Number Specify the ACL ID of this rule. The possible ID of IP Standard ACL is 1-1000. Action Specify the action for packet matched. Select Permit to process the packets, Deny to discard them.
Page 62
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 69 – ACL > IP Extended ACL Parameter Description ACL Number Specify the ACL ID of this rule. The possible ID of IP Standard ACL is 1001-65535. Action Specify the action for packet matched. Select Permit to process the packets, Deny to discard them.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Destination Port Mask Matching packet with a range of destination port. For example source port 23 with mask FFFE means 22~23. The mask options are: 8000, C000, E000, F000, F800, FC00, FE00, FF00, FF80, FFC0, FFE0, FFF0, FFF8, FFFC, FFFE, FFFF.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 70 – ACL > Classmap Parameter Description Classmap ID Specify the classmap ID. The possible value is 1-65535. ACL ID Specify the ACL rule ID to bind. ACL Type Specify the type of the ACL rule.
Page 65
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Policed-DSCP - Assign a new DSCP value to the packets. Policed-Priority - Assign a new 802.1p priority to the packets. In-Profile Action Value Specify the new value of above. When rewriting DSCP tag, the possible value is 0-63;...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Ingress RateLimit Specify the traffic Kbit per second is allowed to be transmitted for an ingress (0,64~1000000 Kbps) port. 0 means no limit. Egress RateLimit Specify the traffic Kbit per second is allowed to be transmitted for an egress (0,64~1000000 Kbps) port.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Parameter Description Priority 0~7 Specify which switch queue to map. The options are Class-0, Class-1, Class-2 and Class-3. Click Apply to submit the changes. 802.1p Port Priority This page is to configure the 802.1p priority for untagged packets receive from each port. Figure 75 –...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Click Add to create a new statistics entry, Reset to clear the value. Parameter Description Select Select a RMON statistics entry to apply the Index The index of the RMON statistics collection. Port The port of the RMON statistics collection.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Interval Specify the time interval for the history collection. Owner Specify the owner of the history entry. Status Specify the status of this history entry. The options are: Valid - The history entry is valid. Under Creation - Invalid - The history entry is invalid and will be deleted.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Interval The time interval in seconds that alarm monitors the MIB variable. Variable The MIB OID of this alarm entry. Sample type The type of the alarm sampling. The options are: Absolute value - To test the MIB variable directly.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots SNMP Trap - Generating a trap message when event is triggered. Log and Trap - Generating both log and trap message when event is triggered. Community Specify the SNMP community string used for the traps. Owner Specify the owner of the alarm entry.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 83 – Statistics > Interface Click 1-12, 13-24 to display the Ethernet related statistics of corresponding ports. Ethernet Statistics This page is to display the Ethernet related statistics of each port. Figure 84 –...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots MSTP MSTP Information This page is to display current MSTP settings and states of the Switch. Figure 86 – Statistics > MSTP > MSTP Information MSTP CIST Port Statistics This page is to display the MSTP traffic statistics of ports. Figure 87 –...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots RSTP RSTP Information This page is to display current RSTP setting and states of the Switch. Figure 89 – Statistics > RSTP > RSTP Information RSTP Port Statistics This page is to display the RSTP traffic statistics of ports. Figure 90 –...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 91 – Statistics > LA > Port LACP Stats Click 1-12, 13-24 to display the Link Aggregation neighbours information of corresponding ports. LA Neighbour Statistics Information This page is to display the information of Link Aggregation neibubours. Figure 92 –...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots 802.1X 802.1X Session Statistics This page is to display the statistics and status of current authenticated users. Figure 93 – Statistics > 802.1X > Session Stats Click 1-12, 13-24 to display the statistics for corresponding ports. RADIUS Server Statistics This page is to display the traffic statistics to RADIUS server.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 98 – Statistics > IP > ICMP Statistics RMON This page is to display the RMON Statistics of the Switch. Figure 99 – Statistics > RMON Click First, Prev, Next, Last to see the first, previous, next or last page of the RMON Statistics. MAC Address Table This page is to show the MAC addresses learned in L2 forwarding database.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Figure 100 – Statistics > MAC Address Table Parameter Description VLAN ID Display the MAC addresses under a given VLAN. MAC Address Display a specific MAC address in FDB. Port Display the MAC addresses learned under a given port.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 11 Using the Command-Line Interface Accessing the Switch This system may be managed out-of-band through the console port on the front panel or in-band using Telnet. The user may also choose the web-based management, accessible through a web browser.
Privileged EXEC Mode admin admin Figure 103 –Connected to an end node via Ethernet cable Privilege Levels TL2-G244 support 15 user privilege levels for commands, the default setting as below. Privilege Levels 2~14 Description User EXEC Mode Not Defined...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Configuration interfaces. Mode Config-vlan Mode The VLAN Configuration Mode is used to configure the commands for VLAN interfaces. MSTP The MSTP Configuration Mode is used to configure multiple spanning tree Configuration specific commands.
A maximum of 15 characters is allowed. A NULL string is not identify info accepted. Default Settings SysName Command Modes Global Configuration Mode User Guidelines This command defines the name of the Switch. Example switch(config)# system name trendnet Command History Version History 1.00.001 This command was introduced. 12-1...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots system contact To enter identification information of a contact person. Command system contact <contact info> Syntax Description A maximum of 50 characters is allowed. A NULL string is not contact info accepted.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command system web-timeout <180-3600 seconds> Syntax Description The web interface logs out the current user when no user 180-3600 seconds activity input for 180-3600 seconds. Default Settings 600 seconds Command Modes Global Configuration Mode User Guidelines This command defines the amount of time the device times out when no user...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Default mode must be dynamic to make this command effective. Note default mode To configure the mode that the IP address of default interface is assigned. Command default mode { manual | dynamic } Syntax Description Manual mode.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced. default restore-file To configure the default restoration file. Command default restore-file <filename> Syntax Description The name of restoration file. filename Default Settings Iss.conf Command Modes Global Configuration Mode...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots set ip http To enable or disable HTTP server. Command set ip http {enable | disable} Syntax Description To enable the embedded HTTP server. enable To disable the embedded HTTP server. disable Default Settings Enable...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command show system information Command Modes Privileged EXEC mode Example switch# show system information Hardware Version : Rev.A1 Firmware Version : 1.00.002 Switch Name : SysName System Contact : SysContact System Location : SysLocation Logging Option...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced. show http server status To display the HTTP server status. Command show http server status Command Modes Privileged EXEC mode Example switch# show http server status HTTP server status : Enabled...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots show line console To display the information of current session. Command show line console Command Modes Privileged EXEC mode Example switch# show line console Current Session Timeout (in secs) = 18000 Command History Version History...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 13 User Account Command User Account Command List username show users listuser username To configure a user account information Command username <user-name> [password <passwd>] [privilege <1-15>] no username <user-name>...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show users Line User Peer-Address 0 con root Local Peer Command History Version History 1.00.001 This command was introduced. listuser To display all existing user information. Command listuser Command Modes Privileged EXEC mode Example...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 14 Management VLAN Command Management VLAN Command List management vlan-list show management vlan management vlan-list To set the VLAN ID for the management VLAN. Command management vlan-list <vlan-list> no management vlan-list <vlan-list>...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots The IP address of Management VLAN interface must be assigned by a DHCP Note server. ip arp max-retries To set the maximum number of ARP request retries. Command ip arp max-retries <value (2-10)> no ip arp max-retries Syntax Number of ARP request retries.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax IP address of the network node. ip address Description MAC address of the network node. hardware address VLAN id Vlan vlan-id(1-4094) Interface type and id of the interface connects to the ARP interface-type entry.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots ip address To configure the IP address of interface. Command ip address <ip-address> <subnet-mask> <gw-address> no ip address <ip-address> Syntax IP address of the interface ip-address Description Subnet mask of the interface subnet-mask IP address of the gateway gw-address...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Information of all DHCP client activities Description Information of DHCP client events. event Information of DHCP client packets packets Information of errors. errors Information of DHCP client binding. bind Default Settings Disabled Command Modes...
Page 105
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command show ip route [ { <ip-address> [<mask>] | bgp | connected | ospf | rip | static | summary } ] Syntax Network address and subnet mask of IP route. <ip-address>...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 16 IP Authorized Manager Command IP Authorized Manager Command List authorized-manager show authorized-managers authorized-manager To set an authorized administrator source IP address, and the services, interfaces, or VLANs that it is allowed to visit. Command authorized-manager ip-source <ip-address>...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots User Guidelines The no form removes the administrator from the list. Example switch(config)# authorized-manager ip-source 10.90.90.100 Command History Version History 1.00.001 This command was introduced. show authorized-managers Display the authorized-manager list. Command show authorized-managers [ip-source <ip-address>] Syntax...
Page 109
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Name of SNMP group GroupName SNMP version 1 is to be used SNMP version 2v is to be used SNMP version 3 is to be used Authentication is required for the SNMP messages auth Authentication is not required for the SNMP messages noauth...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command Modes Global Configuration Mode User Guidelines Before configuring the access settings, the SNMP group has to be created first. Example switch(config)# snmp access oper v2c read operv2readview write operv2writeview notify operv2notifyview nonvolatile Command History Version History...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command snmp engineid <EngineIdentifier> no snmp engineid Syntax Description A string of between 5 and 32 octets expressed in EngineIdentifier hexadecimal that is separated by dots Default Settings 80.00.08.1c.04.46.53 Command Modes Global Configuration Mode User Guidelines SNMP engine ID is unique for each switches...
Page 112
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Default Settings Security Model : v1 Security Name : none Group Name : iso Storage Type : Non-volatile ------------------------------ Security Model : v1 Security Name : ReadOnly Group Name : ReadOnly Storage Type : Non-volatile ------------------------------...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Excludes the object from the list that the SNMP administrator excluded can access Store in volatile memory volatile Store in nonvolatile memory nonvolatile Default Settings View Name : iso Subtree OID : 1 Subtree Mask : 1 View Type : Included...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced snmp trap link-status To enable sending link-status Trap message, and no form disables it Command snmp trap link-status no snmp trap link-status Default Settings Disabled Command Modes...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch#show snmp 0 SNMP Packets Input 0 Bad SNMP Version errors 0 Unknown community name 0 Get request PDUs 0 Get Next PDUs 0 Set request PDUs 0 SNMP Packets Output 0 Too big errors 0 No such name errors 0 Bad value errors...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show snmp community Community Index : NETMAN Community Name : NETMAN Security Name : none Context Name Transport Tag Storage Type : Non-volatile Row Status : Active ------------------------------ Community Index : PUBLIC Community Name : PUBLIC Security Name...
Page 121
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show snmp group Security Model : v1 Security Name : none Group Name : iso Storage Type : Non-volatile Row Status : Active ------------------------------ Security Model : v1 Security Name : ReadOnly Group Name : ReadOnly...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show snmp group access To display the access setting of SNMP group Command show snmp group access Command Modes Privileged EXEC Mode 17-15...
Page 123
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show snmp group access Group Name : iso Read View : iso Write View : iso Notify View : iso Storage Type : Non-volatile Row Status : Active ------------------------------ Group Name : iso...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Read View : ReadWrite Write View : ReadWrite Notify View : ReadWrite Storage Type : Non-volatile Row Status : Active ---------------------------- Command History Version History 1.00.001 This command was introduced show snmp inform statistics To display the recipient information of SNMP traps Command...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots show snmp user To display the SNMP user information Command show snmp user Command Modes Privileged EXEC Mode Example switch# show snmp user Engine ID : 80.00.08.1c.04.46.53 User : initial Authentication Protocol : None Privacy Protocol : None...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command show snmp viewtree Command Modes Privileged EXEC Mode Example switch# show snmp viewtree View Name : iso Subtree OID : 1 Subtree Mask : 1 View Type : Included Storage Type : Non-volatile Row Status : Active...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 18 SSH Command SSH Command List ip ssh debug ssh show ip ssh To activate the SSH server function on the switch. The no format is to turn it off. Command ssh {enable | disable} Syntax Description...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description The supported version of SSH. version compatibility To configure SSH Cipher algorithm. User can choose from cipher DES (Data Encryption Standard) or 3DES (Triple_Data ([des-cbc] Encryption Standard) encryption algorithm in CBC (Cipher [3des-cbc]) Blocking Chain) mode.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 19 SSL Command SSL Command List ip http secure debug ssl show ssl server-cert show ip http secure server status ip http secure To activate SSL server on the switch and configure Cipher and key settings. The no form will deactivate SSL server and all settings.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Default Settings SSL server is disabled. Cipher Suite is RSA-DES-SHA1, RSA-3DES-SHA1, and RSA-EXP1024-DES-SHA1 Command Modes Global Configuration Mode Example switch(config)# ip http secure ciphersuite rsa-null-md5 Command History Version History 1.00.001 This command was introduced debug ssl To enable the debug messages of SSL.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots show ip http secure server status To display the SSL server status Command show ip http secure server status Command Modes Privileged EXEC Mode Example switch# show ip http secure server status HTTP secure server status : Disabled HTTP secure server ciphersuite : RSA-NULL-MD5:...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description IP address of the syslog server ip-address The size of internal logging buffer buffered size (1-200) Enable logging to the console console Specifies the facility that is indicated in the Facility local0~7 message.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description The IP address of mail server ip-address Default Settings No mail server is configured. Command Modes Global Configuration Mode Example switch(config)# mailserver 172.17.0.201 Command History Version History 1.00.001 This command was introduced clear logs Clear the system log buffers...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Enables the SNTP. enable Disables the SNTP. disable Default Settings Disable Command Modes Global Configuration Mode Example switch(config)# set sntp enable Command History Version History 1.00.001 This command was introduced set sntp dst To enable/disable the Daylight Saving Time (DST) function of SNTP.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Time that DST startis from from Specify the month that DST starts. january ~ december Specify the day that DST starts. day (1-31) Specify the hour that DST starts. hour (0-23) Specify the minute that DST starts.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command sntp primary-ip <ip-address> Syntax Description Specify the IP address of the primary SNTP server. ip-address Command Modes Global Configuration Mode Example switch(config)# sntp primary-ip 172.17.5.254 Command History Version History 1.00.001 This command was introduced sntp secondary-ip...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch(config)# sntp timezone offset – 8 0 Command History Version History 1.00.001 This command was introduced show clock To display the system date and time. Command show clock Command Modes Privileged EXEC Mode Example switch# show clock...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 22 Configuration Command Configuration Command List write copy startup-config copy erase write To save the running configuration. Command write flash:filename startup-config tftp://ip-address/filename } Syntax Description Write to a designated flash driver with designated file flash:filename name.
Page 144
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# copy startup-config flash:backupstarup Command History Version History 1.00.001 This command was introduced copy To replace the startup configuration by a another configuration file in remote TFTP site or NV-RAM. Command copy { tftp://ip-address/filename startup-config | flash: filename startup-config }...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 24 Reboot Command Reboot Command List reload reload Reboot the Switch Command reload Command Modes Privileged EXEC Mode Example switch# reload Command History Version History 1.00.001 This command was introduced If the Switch reboots without write the running configurations, the last Note configuration wrote in NV-RAM will be loaded.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 25 Port Manager Command Port Manager Command List monitor session negotiation speed duplex flowcontrol show flow-control show mdi-mdix show port-monitoring monitor session To enable and configure the port mirroring function.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command Modes Global Configuration Mode User Guidelines 1. Using no form to disable the port mirroring function. 2. Destination port and source port have to be counfigured separately. 3. A port-channel can be mirrored, however, a port-channel port cannot. Example switch(config)# monitor session 1 destination interface fa 0/1 switch(config)# monitor session 1 source interface fa 0/2 both...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots User Guidelines The configured port speed and duplex settings only takes effect when auto-negotiation disabled. Example switch(config-if)# speed 100 Command History Version History 1.00.001 This command was introduced duplex To set the port duplex mode. Command duplex { full | half } Syntax Description...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced To set MDI or MDIX mode for ports. Command mdi { auto | mdi | mdix } Syntax Description Port performs the auto MDI/MDIX function. auto Port fixed at MDI mode.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots show mdi-mdix To display the MDI/MDIX setting on ports. Command show mdi-mdix [ interface <interface-type> <interface-id>] Syntax Description Specify which interface to show MDI/MDIX setting interface Interface-type including Fa (Fast Ethernet) or Gi (Gigabit interface-type Ethernet).
Page 152
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command show port-monitoring Command Modes Privileged EXEC Mode Example switch# show port-monitoring Port Monitoring is enabled Monitor Port : Fa0/9 Port Ingress-Monitoring Egress-Monitoring ---- ------------------ ----------------- Fa0/1 Enabled Enabled Fa0/2 Disabled Disabled Fa0/3...
The default port membership is tagged. Command Modes Config-vlan Mode User Guidelines The untagged port must be the subset of member port. Example switch(config-vlan)# ports fa 0/1-5 untagged fa 0/5 forbidden fa 0/7 name trendnet Command History Version History 1.00.001 This command was introduced 26-3...
Page 157
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command show vlan [brief | id <vlan-range> | summary] Syntax Description Display the brief of VLAN information. brief Limited a range of VLAN to display the information. id <vlan-range> The vlan-range format is a-b, b should be larger than a. Display the number of VLAN.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Name : Status : Dynamic Gvrp ---------------------------------------------------- Command History Version History 1.00.001 This command was introduced show vlan device info To display the VLAN settings and detailed information of the device. Command show vlan device info Command Modes...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example Single Instance: switch# show vlan device info Vlan device configurations -------------------------- Vlan Status : Enabled Vlan Oper status : Enabled Gvrp status : Disabled Gvrp Oper status : Disabled Bridge Mode : Customer Bridge Traffic Classes...
Page 161
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command Modes Privileged EXEC Mode User Guidelines System will display VLAN configurations for all port when executing the command without a port parameter. 26-9...
Page 162
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example Single Instance: switch# show vlan port config port fa 0/1 Vlan Port configuration table ------------------------------- Port Fa0/1 Port Vlan ID Port Acceptable Frame Type : Admit All Port Ingress Filtering : Enabled Port Mode : Hybrid...
Page 163
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Default Priority : 0 ------------------------------------------------------- Port Fa0/3 Port Vlan ID : 1 Port Acceptable Frame Type : Admit All Port Ingress Filtering : Disabled Port Mode : Hybrid Port Gvrp Status : Enabled Port Gmrp Status : Enabled Port Gvrp Failed Registrations : 0 Gvrp last pdu origin : 00:25:64:93:1c:35...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Specify which port to enable GVRP function. interface-type Interface-type including Fa (Fast Ethernet) or Gi (Gigabit interface-id Ethernet). Interface-id is slot/port number. Enables GVRP on the port. enable Disables GVRP on the port.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots debug garp To enable the debug mode of GARP function. Command debug garp { global | [{protocol | gvrp | redundancy} [initshut] [mgmt] [data] [ctpl] [dump] [os] [failall] [buffer] [all]]} no debug garp { global | [{protocol | garp | redundancy} [initshut] [mgmt] [data] [ctpl] [dump] [os] [failall] [buffer] [all]]...
Page 168
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Specify which port to show GVRP timer setting. port Interface-type including Fa (Fast Ethernet) or Gi (Gigabit interface-type Ethernet). interface-id Interface-id is slot/port number. Command Modes Privileged EXEC Mode User Guidelines System will display timer settings for all port when executing the command without a port parameter.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command spanning-tree compatibility {stp|rst|mst} no spanning-tree compatibility Syntax Description Compatible wirh STP. Compatible with RSTP. Compatible with MSTP. Default Settings Command Modes Global Configuration Mode User Guidelines Using no form to reset the STP compatibility to default. Example switch(config)# spanning-tree compatibility stp Command History...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots spanning-tree pathcost dynamic To enable the dynamic pathcost according to the port speed.. Command spanning-tree pathcost dynamic no spanning-tree pathcost dynamic Default Settings Disable Command Modes Global Configuration Mode User Guidelines 1.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots spanning-tree timers To set the timer of spanning tree. Command spanning-tree {forward-time <seconds(4-30)> hello-time <seconds(1-2)> | max-age <seconds(6-40)>} no spanning-tree { forward-time | hello-time | max-age } Syntax Description The time period that a port changes the STP state from forward-time blocking to forwarding.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced spanning-tree restricted-role To enable the root guard function to prevent the port becoming a root port. Command spanning-tree restricted-role no spanning-tree restricted-role Default Settings Disable Command Modes...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch(config)# shutdown spanning-tree Command History Version History 1.00.001 This command was introduced clear spanning-tree counters To clear the spanning tree counters. Command clear spanning-tree counters Command Modes Global Configuration Mode Example switch(config)# clear spanning-tree counters Command History...
Page 176
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Displays the MSTP global debug messages. global Displays all RSTP/MSTP debug messages. Displays the error code debug messages. errors Displays the initial and shutdown debug messages. init-shut Displays the management related debug messages. management Displays the memory related debug messages.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots show spanning-tree To display the spanning port states, statistics, settings and detailed information. Command show spanning-tree [{ summary | blockedports | pathcost method }] Syntax Description Display the summary of port states. summary Display current block port number.
Page 178
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example Single Instance: switch# show spanning-tree Root Id Priority 32768 Address 00:18:8b:bf:75:30 Cost 0 Port 0 [0] This bridge is the root Max age 20 Sec, forward delay 15 Sec Spanning tree Protocol Enabled Bridge Id Priority 32768...
Page 179
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots S-VLAN Component: MST00 is executing the mstp compatible Multiple Spanning Tree Protocol Bridge Id Priority 32768 Address 00:18:8b:bf:75:30 Hello Time 2 sec, Max Age 20 sec, Forward Delay 15 sec Dynamic Path Cost is Enabled Name Role...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots show spanning-tree active To display the spanning tree information on active ports. Command show spanning-tree active [detail] Syntax Description Display the details of spanning tree bridge. detail Command Modes Privileged EXEC Mode 28-12...
Page 181
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example Single Instance: switch# show spanning-tree active Root Id Priority 8192 Address 00:74:24:00:01:00 Cost 2000000 Port Fa0/1 Hello Time 2 Sec, Max Age 20 Sec, Forward Delay 15 Sec Spanning Tree Enabled Protocol RSTP Bridge Id Priority 32768 Address 00:18:8b:bf:75:30...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots show spanning-tree bridge To display the spanning tree bridge settings. Command show spanning-tree bridge [{ address | forward-time | hello-time | id |max-age | protocol | priority | detail }] Syntax Description Display the MAC address of spanning tree bridge.
Page 183
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example Single Instance: switch# show spanning-tree bridge Bridge ID HelloTime MaxAge FwdDly Protocol --------- --------- ------ ------ -------- 80:00:00:74:24:00:01:00 2000 rstp switch# show spanning-tree bridge address Bridge Address is 00:74:24:00:01:00 switch# show spanning-tree bridge forward-time Bridge Forward delay is 15 sec switch# show spanning-tree bridge hello-time...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots MST00 00:74:24:00:01:00 Switch - cust1 MST00 00:74:24:00:01:02 Command History Version History 1.00.001 This command was introduced show spanning-tree interface To display the spanning tree states, statistics, settings information on a port. Command show spanning-tree interface <interface-type>...
Page 185
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example Single Instance: switch# show spanning-tree interface fa 0/1 Role State Cost Prio Type ---- ----- ---- ---- ---- Root Forwarding 2000000 128 SharedLan switch# show spanning-tree interface fa 0/1 cost Port cost is 2000000 switch# show spanning-tree interface fa 0/1 priority Port Priority is 128...
Page 186
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots BPDUs : sent 1479 , recieved 3458 Multiple Instance: switch# show spanning-tree interface fa 0/1 Switch - default Role State Cost Prio Type ---- ----- ---- ---- ---- Root Forwarding 2000000 128 SharedLan switch# show spanning-tree interface fa 0/1 cost Port cost is 2000000...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots switch# show spanning-tree interface fa 0/1 detail Switch – default Port 1 [Fa0/1] is Root , Forwarding Port PathCost 2000000, Port Priority 128, Port Identifier 128.1 Designated Root has priority 8192, address 00:18:8b:bf:75:30 Designated Bridge has priority 8192, address 00:18:8b:bf:75:30 Designated Port Id is 128.1, Designated PathCost 0 No of Transitions to forwarding State :1...
Page 188
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show spanning-tree root Root ID RootCost MaxAge FwdDly RootPort ------- --------------- ------ -------- 80:00:08:00:1f:3f:73:26 0 switch# show spanning-tree root address Root Bridge Address is 08:00:1f:3f:73:26 switch# show spanning-tree root cost Root Cost is 2000000 switch# show spanning-tree root forward-time Forward delay is 15 sec...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command spanning-tree mst configuration Command Modes Global Configuration Mode User Guidelines Spanning tree mode must be MST before entering the MSTP Configuration Mode. Example switch(config)# spanning-tree mst configuration switch(config-mst)# Command History Version History 1.00.001...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Default Settings Command Modes Global Configuration Mode User Guidelines Using no form to reset the max instance number to default. Example switch(config)# spanning-tree mst max-instance 16 Command History Version History 1.00.001 This command was introduced instance...
Default Settings 00: 00: 00: 00: 00: 00 Command Modes MSTP Configuration Mode User Guidelines Using no form the reset the name to default. Example switch(config-mst)# name trendnet Command History Version History 1.00.001 This command was introduced revision To set the revision number for the MST reigon.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command Modes Interface Configuration Mode User Guidelines Use no form to reset the hello time value to default. Example switch(config-if)# spanning-tree mst hello-time 1 Command History Version History 1.00.001 This command was introduced show spanning-tree mst To display the information of MST instances.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show spanning-tree mst interface To display the MSTP status, statistics and current setting on interfaces. Command show spanning-tree [<instance-id(1-64)>] interface <interface-type> <interface-id>...
To display current multiple spanning tree settings. Command show spanning-tree mst configuration Command Modes Privileged EXEC Mode Example Single Instance: switch# show spanning-tree mst configuration Name [trendnet] Revision 2 Instance Vlans mapped -------- ------------------------------------------ 1,3-1024,1025-2048,2049-3072,3073-4094 ------------------------------------------------------- Multiple Instance: switch# show spanning-tree mst configuration...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Specify the value of LACP system priority. 0-65535 Default Settings 32768 Command Modes Global Configuration Mode User Guidelines The system priority decides the standby or active links in a aggregation when the number of member port exceeds the maximum number of the etherchannel that Switch supported.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced channel-group To join a port to a channel group. Command channel-group <channel-group-number(1-65535)> mode {active | passive | on} no channel-group Syntax Description Specify which channel group to configure.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots User Guidelines The port priority decides the standby or active links in a aggregation when the number of member port exceeds the maximum number of the etherchannel that Switch supported. Example switch(config-if)# lacp port-priority 1 Command History...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch(config-if)# lacp wait-time 0 Command History Version History 1.00.001 This command was introduced shutdown port-channel To shutdown the port channel group. Command shutdown port-channel no shutdown port-channel Default Settings Active Command Modes Global Configuration Mode...
Page 201
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots User Guidelines System will display the global information and the summary of all port channel groups when executing this command without any keyword. 30-6...
Page 202
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show etherchannel Port-channel Module Admin Status is enabled Port-channel Module Oper Status is enabled Port-channel System Identifier is 00:74:24:00:01:00 Maximum ports per Port Channel is 8 with maximum 8 active ports Channel Group Listing --------------------- Group : 1...
Page 203
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Default Port = None switch# show etherchannel 1 load-balance Channel Group Listing --------------------- Group : 1 ---------- Source & Destination MAC Address switch# show etherchannel 1 port Channel Group Listing --------------------- Group: 1 ----------...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Number of Ports = 1 HotStandBy port = null Port state = Port-channel Ag-Not-Inuse Protocol = LACP MAC selection = Dynamic Default Port = None switch# show etherchannel 1 summary Port-channel Module Admin Status is enabled Port-channel Module Oper Status is enabled Port-channel System Identifier is 00:74:24:00:01:00...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command Modes Privileged EXEC Mode Example switch# show lacp 1 counters LACPDUs LACPDUs Port Sent Recv Pkts Err ------------------------------------------------ Channel group: 1 ------------------ Gi0/1 788 704 Gi0/2 636 596 switch# show lacp 1 neighbor Flags: A - Device is in Active mode P - Device is in Passive mode...
Page 206
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command show interfaces [<interface-type> <interface-id> etherchannel Syntax Description Specify the information of which port to show. interface-type Interface-type including Fa (Fast Ethernet) or Gi (Gigabit interface-id Ethernet). Interface-id is slot/port number. Command Modes Privileged EXEC Mode User Guidelines...
Page 207
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show interface gi 0/1 etherchannel Port : Gi0/1 ------------- Port State = Down, Not in Bundle Channel Group : 1 Mode : Active Pseudo port-channel = Po1 LACP port-priority = 128 LACP Wait-time = 2 secs LACP Admin Port = 25 LACP Activity : Active...
Page 209
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots dot1x system-auth-control To enable 802.1X authentication on the Switch. Command dot1x system-auth-control no dot1x system-auth-control Default Settings Disable Command Modes Global Configuration Mode User Guidelines Using no form to disable the 802.1X authentication. Example switch(config)# dot1x system-auth-control Command History...
Page 210
2. When create a user account without permission, auth-timeout and interface values, system will assign default value to this account. Example switch(config)# dot1x local-database trendnet password trendnet123 permission deny Command History Version History 1.00.001 This command was introduced radius-server host To configure the details of RADIUS server.
Page 211
Command Modes Global Configuration Mode User Guidelines When configure a RADIUS server without timeout and retransmit parameter, system will apply the default values. Example switch(config)# radius-server host 172.17.5.111 key trendnet Command History Version History 1.00.001 This command was introduced dot1x control-direction To choose the authentication control direction on ports.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots User Guidelines Using no form to reset the number of retry to default. Example switch(config-if)# dot1x max-req 10 Command History Version History 1.00.001 This command was introduced dot1x max-start To set the maximum EAPOL retries of the authenticator. Command dot1x max-start <count(1-65535)>...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Default Settings Force-authorized Command Modes Interface Configuration Mode Example switch(config-if)# dot1x port-control auto Command History Version History 1.00.001 This command was introduced dot1x reauthenitcation To enable the periodic re-authentication on ports. Command dot1x reauthenitcation no dot1x reauthenitcation...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description The period that Switch will not do anything after a failed quiet-period authentication. value (0-65535) The period between re-authentication attempts. reauth-period value (1-65535) The period that Switch waits for the re-transmission to the server-timeout RADIUS server.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Displays all RADIUS debug messages. Displays the error code debug messages. errors Displays the event related debug messages. events Displays the packet related debug messages. packets Displays the server response related debug messages. responses Displays the timer related debug messages.
Page 218
= 00:00:00:00:00:00 switch# show dot1x local-database Pnac Authentication Users Database ----------------------------------- User name : trendnet Protocol : 4 Timeout : 0 seconds Ports : Fa0/1, Fa0/2, Fa0/3, Fa 0/4, Fa 0/5, Fa 0/6, Fa 0/7, Fa 0/8, Fa 0/9, Fa 0/10, Fa 0/11, Fa 0/12, Fa 0/13, Fa 0/14,...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Fa 0/22, Fa 0/23, Fa 0/24 Permission : Allow --------------------------------- Command History Version History 1.00.001 This command was introduced show radius server To display current status and settings of RADIUS servers Command show radius server Command Modes...
Page 220
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show radius statistics Radius Server Statistics ------------------------- Index : 1 Radius Server Address : 172.17.5.135 UDP port number : 1812 Round trip time : 0 No of request packets : 7 No of retransmitted packets : 72 No of access-accept packets : 0 No of access-reject packets : 0...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command ip igmp snooping mrouter <interface-type> <0/a-b, 0/c, ...> no ip igmp snooping mrouter <interface-type> <0/a-b, 0/c, ...> Syntax Description Specify the type and ID of the static multicast router port. interface-type Interface-type including Fa (Fast Ethernet) or Gi (Gigabit 0/a-b, 0/c, ...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command ip igmp snooping port-purge-interval <(130 - 1225) seconds> no ip igmp snooping port-purge-interval Syntax Description Specify the port purge interval. (130-1225) seconds Default Settings 260 seconds Command Modes Global Configuration Mode User Guidelines Using no form to reset the port purge interval to default.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots received a IGMPv2 leave message. Command ip igmp snooping retry-count <1 - 5> no ip igmp snooping retry-count Syntax Description Specify the maximum retries for group specific queries. 1 - 5 Default Settings Command Modes Global Configuration Mode...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command ip igmp snooping fast-leave no ip igmp snooping fast-leave Default Settings Disable Command Modes Config-vlan Mode Example switch(config-vlan)# ip igmp snooping fast-leave Command History Version History 1.00.001 This command was introduced ip igmp snooping querier To configure the switch as the IGMP querier in a VLAN.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots User Guidelines Using no form the restart the snooping. Example switch(config)# shutdown snooping Command History Version History 1.00.001 This command was introduced debug ip igmp snooping To enable the debug mode of IGMP snooping. Command debug ip igmp snooping {[init] [resources] [tmr] [src] [grp] [qry] [vlan] [pkt] [fwd] [mgmt] [redundancy] | all }...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show ip igmp snooping To display current settings of IGMP snooping function. Command show ip igmp snooping [Vlan <vlan id>] Syntax Description Vlan vlan id Command Modes Privileged EXEC Mode...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show ip igmp snooping globals To display the current global settings of IGMP snooping function. Command show ip igmp snooping globals Command Modes Privileged EXEC Mode Example...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example Single Instance: switch# show ip igmp snooping mrouter Vlan Ports ----- ------ 1 Gi0/1(dynamic), Gi0/2(static) 2 Gi0/3(static), Gi0/4(dynamic) Multiple Instance: switch# show ip igmp snooping mrouter Switch cust1 Vlan Ports ----- ------ 1 Gi0/1(static) 2 Gi0/2(static)
Page 233
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show ip igmp snooping statistics vlan 1 Snooping Statistics for VLAN 1 General queries received : 0 Group specific queries received : 0 Group and source specific queries received : 0 ASM reports received : 477 SSM reports received : 0 IS_INCLUDE messages received : 0...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots show mac-address-table To display the MAC address data learned or configured in MAC address table. Command show mac-address-table [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [{interface <interface-type> <interface-id>}] Syntax Description To display MAC addresses belong to a specific VLAN vlan vlan-range range.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command show mac-address-table aging-time Command Modes Privileged EXEC Mode Example switch# show mac-address-table aging-time Mac Address Aging Time: 300 Command History Version History 1.00.001 This command was introduced show mac-address-table count To display the statistics for each kind of MAC address in MAC address table.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description To display MAC addresses belong to a specific VLAN vlan vlan-range range. Specify a specific MAC address to display. address aa:aa:aa:aa:aa:aa To display MAC addresses under a specific port. interface Interface-type including Fa (Fast Ethernet), Gi (Gigabit interface-type...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show mac-address-table static unicast To display the static unicast MAC address in MAC address table. Command show mac-address-table static unicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [{interface <interface-type>...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 34 Port Security Command Port Security Command List max learning address show max-learning-address max learning address To limits the number of MAC address learned from a port. Command max learning address <address number(0-64)>...
Page 243
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show max-learning-address Port Port Security Status Max Learning Address ---- ------------------ ----------------- Fa0/1 Enabled Fa0/2 Disabled Fa0/3 Enabled Fa0/4 Disabled Fa0/5 Enabled Fa0/6 Disabled Fa0/7 Enabled Fa0/8 Disabled Fa0/9 Disabled Fa0/10...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command ip access-list { standard <access-list-number (1-1000)> | extended <access-list-number (1001-65535)> } no ip access-list { standard <access-list-number (1-1000)> | extended <access-list-number (1001-65535)> } Syntax Description Specify the ID to a standard IP access control list. standard access-list-number (1-1000)
Page 246
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Matching packets with any source MAC address. Matching packets with a specific source MAC address. host mac-address Matching packets with any destination MAC address. Matching packets with a specific destination MAC address. host mac-address Matching packets with ether type aarp, 0x80F3(33011).
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command Modes MAC Access List Configuration Mode Example switch(config-ext-macl)# permit host 11-22-33-44-55-66 any msdos Command History Version History 1.00.001 This command was introduced deny (Standard IP Access List Configuration) To configure a rule that packets matched will be filtered. Command deny { any | host <src-ip-address>...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Matching packet with any source IP address. Matching packet with a specific source IP address. host src-ip-address Matching packet with a range of source IP address. For src-ip-address example 172.17.5.1 with mask 255.255.255.0 means mask 172.15.5.0~255.
Page 250
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Matching all IP packets. Matching all OSPF packets. ospf Matching all PIM packets. Matching packets with specific protocol type. protocol-type (1-255) Matching packet with any source IP address. Matching packet with a specific source IP address.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots permit (Extended IP Access List Configuration) To configure a rule that packets matched will be processed. Command permit { ip | ospf | pim | <protocol-type (1-255)>} { any | host <src-ip-address>...
Page 252
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Matching all IP packets. Matching all OSPF packets. ospf Matching all PIM packets. Matching packets with specific protocol type. protocol-type (1-255) Matching packet with any source IP address. Matching packet with a specific source IP address.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Matching packet with any source IP address. Matching packet with a specific source IP address. host src-ip-address Matching packet with a range of source IP address. For src-ip-address example 172.17.5.1 with mask 255.255.255.0 means mask 172.15.5.0~255.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots ip access-group To apply an IP access control list from the port. Command ip access-group <access-list-number (1-65535)> no ip access-group [<access-list-number (1-65535)>] Syntax Description access-list-number (1-65535) Command Modes Interface Configuration Mode User Guidelines Using no form to dissociate ACL from the port.
Page 256
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced 35-13...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 36 Classmap Command Classmap Command List class-map match access-group show class-map class-map To create or enter a class map. Command class-map <class-map-number(1-65535)> no class-map <class-map-number(1-65535)> Syntax Description Specify the class map ID.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots User Guidelines The access control list rule must be created before associating. Example switch(config-cmap)# match access-group mac-access-list 1 Command History Version History 1.00.001 This command was introduced show class-map To display the settings of class maps. Command show class-map [<class-map-num(1-65535)>] Syntax Description...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots User Guidelines Class map must be created before associating. Example switch(config-pmap)# class 1 Existing Policy-map configurations have been deleted. Please apply the policy-map to make it active. switch(config-pmap-c)# Command History Version History 1.00.001...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch(config-pmap-c)# police 64 exceed-action drop Command History Version History 1.00.001 This command was introduced show policy-map To display the settings of a policy map. Command show policy-map [<policy-map-num(1-65535)> [class <class-map-num(1-65535)>] Syntax Description policy-map-num...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command Modes Interface Configuration Mode User Guidelines The no form is to disable the rate limiting on a port. Example switch(config-if)# rate-limit ingress 64 Command History Version History 1.00.001 This command was introduced show rate-limit To display the current rate-limit setting of interfaces Command...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Chapter 39 Storm Control Command Storm Control Command List storm-control pkt-type storm-control pkt-type To enable and configure the details of the storm control function. Command storm-control pkt-type { broadcast-only | multicast-broadcast dlf-multicast-broadcast rate-level <rate-level...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command Modes Privileged EXEC Mode Example switch# show vlan traffic-classes Traffic Class table --------------------- Priority Traffic Class --------- ------------- Command History Version History 1.00.001 This command was introduced show vlan port config To display the VLAN settings of ports Command show vlan port config [{port <interface-type>...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show dscp To display the current dscp setting. Command show dscp Command Modes Privileged EXEC Mode Example switch# show dscp DSCP is disabled Command History Version History...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Specify the alarm number. number (1-65535) The MIB OID to set alarm. mib-object-id (255) The time interval in seconds that alarm monitors sample-interval-time the MIB variable. (1-2147482647) To test the MIB variable directly. absolute To test the change between samples of a MIB delta...
1. RMON function must be enabled and RMON event must be configured before configuring alarms. 2. Using no form to delete events from RMON event table. Example switch(config)# rmon event 1 description broadcast-too-high log owner trendnet trap redalert Command History Version History 1.00.001...
User Guidelines 1. RMON function must be enabled and RMON event must be configured before configuring alarms. 2. Using no form to disable the statistics collection.. Example switch(config-if)# rmon collection stats 1 owner trendnet Command History Version History 1.00.001 This command was introduced...
Page 274
RMON is enabled switch# show rmon statistics 1 alarms events history overview RMON is enabled Collection 1 on Fa0/5 is active, and owned by trendnet, Monitors ifEntry.1.5 which has Received 0 octets, 0 packets, 0 broadcast and 0 multicast packets,...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command copy tftp://ip-address/filename flash: filename}{ tftp://ip-address/filename | flash: filename} Syntax Description The IP address the remote tftp server and the tftp://ip-address/filename filename you would like to copy from. The path and filename of the local file you flash: filename would like to copy from.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots help To list all the command starting with the given keyword and also display the description of the command. Command help <command> Syntax Description Specify which command you would like to get the help. command Command Modes All Modes...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# clear screen Command History Version History 1.00.001 This command was introduced lock To lock the command line interface to prevent unauthorized user accessing the Switch. Command lock Command Modes Privileged EXEC Mode User Guidelines Entering the password of any privilege 15 user to unlock.
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Specify which user to configure the buffer size. user name Specify the number of buffer size. no.of buffers (1-200) Command Modes Global Configuration Model Example switch(config)# cmdbuffs root 200 Command History Version History...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command space flash: Command Modes Privileged EXEC Mode Example switch# space flash: Command History Version History 1.00.001 This command was introduced space memory: To display the space of DRAM remained Command space memory: Command Modes...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command shutdown no shutdown Default Settings Interfaces had been created are active by default. Command Modes Interface Configuration Mode User Guidelines The no form reactivates the interface. Example switch(config-if)# shut down Command History Version History...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Syntax Description Specify the information of which interface to display. interface-type Interface-type including Fa (Fast Ethernet) or Gi (Gigabit interface-id Ethernet). Interface-id is slot/port number. Display the link status and protocol status of the interface description Display the flow control setting and pause frame statistic flowcontrol...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Command show interface mtu [{ Vlan <vlan-id (1-4094)> | port-channel <port-channel-id (1-65535)> <interface-type> <interface-id> }] Syntax Description VLAN ID Vlan vlan-id (1-4094) Port channel ID port-channel port-channel-id (1-65535) Specify which interface to show the mtu setting. interface-type Interface-type including Fa (Fast Ethernet) or Gi (Gigabit interface-id...
Page 287
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Example switch# show interface fa 0/12 counters Port InOctet InUcast InDiscard InErrs InHCOctet ---- ------- ------- --------- ------ --------- Fa0/12 30159626 8763 30159626 Port OutOctet OutUcast OutDiscard OutErrs OutHCOctet ---- -------- -------- ----------...
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots Technical Specifications Hardware Standards IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3z 1000BASE-X SX/LX IEEE 802.3x Flow Control and Back Pressure IEEE 802.3ad Link Aggregation/Port Trunking (LACP) IEEE 802.1d Spanning Tree (STP) IEEE 802.1w Rapid Spanning Tree (RSTP) IEEE 802.1s Multiple Spanning Tree (MSTP)
Page 289
24-Port Gigabit Layer 2 Switch w/ 4 Shared Mini-GBIC Slots VLAN Asymmetric VLAN 802.1Q Tagged VLAN and Dynamic GVRP Up to 256 static/dynamic groups IGMP Support IGMP Snooping v1/2 Up to 64 multicast entries Port Mirror RX, TX, or both Security MAC Address learning, ACL L2/L3/L4 User Authentication: 802.1X Port-Based Network Access Control,...
AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer.
Page 291
Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt...