TRENDnet TL2-E284 Quick Installation Manual
Hide thumbs
Also See for TL2-E284:
- Specifications (3 pages) ,
- Quick installation manual (15 pages) ,
- User manual (293 pages)
Subscribe to Our Youtube Channel
Related Manuals for TRENDnet TL2-E284
Summary of Contents for TRENDnet TL2-E284
-
Page 2: Table Of Contents
T a b le o f C o n te n ts English 1. B efore You S tart 2. H ardw are Installation 3. LEDs 4. C onfigure the Switch Troubleshooting Version 11.05.2010... -
Page 3: English
1. Before You Start P a c ka g e C o n te n ts • TL2-E284 • Multi-Language Q uick Installation Guide • CD-ROM (User's Guide) • RS-232 cable (3 m / 9.8 ft.) • Power Cord (1.8 m / 5.9 ft.) •... -
Page 4: Hardware Installation
Note: The Mini-GBIC slots are shared with port 25 and 26 Gigabit Ethernet ports. When the Mini-GBIC slots are in use, port 25 and 26 Gigabit Ethernet ports are disabled. 1. Connect the P ow er C ord to the TL2-E284 and then to a power outlet. -
Page 5: Leds
3. LEDs PW R (Power) 24-Port 1 0 / 1 0OMbps layer 2 Managed Switch TLE-EBB4 ® T f f e n o n e T 1 1 I V » 11 i l M i? it ii » a 4 * • to ia u i» i» » a a* a»... - Page 6 Sequence Definition Device Status LED Color Green Solid Device powered On PW R (Power) O ff Device powered O ff Device is ready Green Solid SYS (System ) O ff Device is not ready Ethernet LED (RJ-45) Color Sequence Definition Solid 100/200M bps (Half/Full Duplex) Connected (per port) 100/200M bps (Half/Full Duplex) Data...
-
Page 7: Configure The Switch
192.168.10.200. (Refer to Troubleshooting section on how to configure TCP/IP settings on your PC.) 2. There are three methods of configuring the TL2-E284: Web Browser, Console Port and Telnet. 1. U s in g W e b B ro w s e r 1. - Page 8 Note: A terminal program such as HyperTerminal is required to configure the switch via the Console Port. The instructions shown below demonstrates how to configure the Switch on a W indows PC using HyperTerminal. 1. Connect the RS-232 cable from a serial port on your PC to the console port on the switch.
- Page 9 5. Enter the following, click A p p ly and then click OK, Bits per second: Data bits: Parity: None Stop bits: Flow control: None 6. Press the Enter Key, 7. Enter the U ser Name for login, Then press the Enter, Then Enter the Password and then press Enter, By default...
-
Page 10: Register Your Product
Configuration is now complete For detailed information regarding the TL2-E284 configuration and advanced settings, please refer to User's Guide included on the Utility CD-ROM, or TRENDnet's website at http://www,trendnet,com , Register Your Product To ensure the highest level of customer service and support, please take a moment to w w w .tre n d n e t.c o m /re g is te r... -
Page 11: Troubleshooting
T ro u b le s h o o tin g 1. H ow d o I co n fig u re TCP/IP s e ttin g s on m y co m p u ter? W in d o w s 7 adtitess O b ta in an !P a u tom ab taly... - Page 12 “ The page c a n n o t be d is p la ye d .”...
- Page 13 & Declaration of Conformity TREflDnET C om pany In form ation: Company Name: TRENDnet, Inc. Company Address: 20675 Manhattan Place Torrance, CA 90501 Product In form ation: Product Description: 24-Port lO/lOOMbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots...
- Page 14 Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation.
- Page 15 Copyright © 2010, All Rights Reserved. TRENDnet.
Need help?
Do you have a question about the TL2-E284 and is the answer not in the manual?
Questions and answers